Comments (5)
I second this, using this fingerprint sensor:
https://www.adafruit.com/product/4651
When purposely using different fingers during enrolling, a mismatched error is expected but it does not occur.
from adafruit-fingerprint-sensor-library.
I second this, using this fingerprint sensor: https://www.adafruit.com/product/4651
When purposely using different fingers during enrolling, a mismatched error is expected but it does not occur.
I also have this problem.
from adafruit-fingerprint-sensor-library.
I can reliably recreate this behavior with PID 4750 mentioned in initial post above.
But it's working OK testing with PID 4651.
Here's with the same finger, just to prove it does match as expected:
Adafruit Fingerprint sensor enrollment
Found fingerprint sensor!
Reading sensor parameters
Status: 0x4
Sys ID: 0x0
Capacity: 200
Security level: 3
Device address: FFFFFFFF
Packet len: 128
Baud rate: 57600
Ready to enroll a fingerprint!
Please type in the ID # (from 1 to 127) you want to save this finger as...
Enrolling ID #1
Waiting for valid finger to enroll as #1
........................................................Image taken
Image converted
Remove finger
ID 1
Place same finger again
.................................................Image taken
Image converted
Creating model for #1
Prints matched!
ID 1
Stored!
Ready to enroll a fingerprint!
Please type in the ID # (from 1 to 127) you want to save this finger as...
And here's with using different fingers. Tried four times but it never saw them as same.
Adafruit Fingerprint sensor enrollment
Found fingerprint sensor!
Reading sensor parameters
Status: 0x4
Sys ID: 0x0
Capacity: 200
Security level: 3
Device address: FFFFFFFF
Packet len: 128
Baud rate: 57600
Ready to enroll a fingerprint!
Please type in the ID # (from 1 to 127) you want to save this finger as...
Enrolling ID #1
Waiting for valid finger to enroll as #1
...................................................................................................................Image taken
Image converted
Remove finger
ID 1
Place same finger again
.........................................Image taken
Image converted
Creating model for #1
Fingerprints did not match
Ready to enroll a fingerprint!
Please type in the ID # (from 1 to 127) you want to save this finger as...
Enrolling ID #1
Waiting for valid finger to enroll as #1
..........................................................Image taken
Image converted
Remove finger
ID 1
Place same finger again
........................................Image taken
Image converted
Creating model for #1
Fingerprints did not match
Ready to enroll a fingerprint!
Please type in the ID # (from 1 to 127) you want to save this finger as...
Enrolling ID #1
Waiting for valid finger to enroll as #1
............................................................................Image taken
Image converted
Remove finger
ID 1
Place same finger again
........................................................................Image taken
Image converted
Creating model for #1
Fingerprints did not match
Ready to enroll a fingerprint!
Please type in the ID # (from 1 to 127) you want to save this finger as...
from adafruit-fingerprint-sensor-library.
Issue #120 is a repeat for PID 4651 behavior.
from adafruit-fingerprint-sensor-library.
Is there any progress on this? :)
I'm in the same boat than the initial author...
from adafruit-fingerprint-sensor-library.
Related Issues (20)
- arduino issue HOT 1
- Library not working well for sensor GROW R503 on ATMega 2560 when using real UART HOT 1
- Copy fingerprint data to a new sensor HOT 1
- Cannot use setBaudRate() to change from default 57600bps HOT 9
- 1:1 matching HOT 1
- Fingerprint sensor constantly flashing. HOT 4
- Incorrectly matched fingerprints for: Rugged Panel Mount Fingerprint Sensor with Bi-Color LED Ring - R503 HOT 1
- More colors for LED color control HOT 3
- Type error: uint8_t - cycle is forever HOT 1
- storeModel by fingerprint templae HOT 1
- Library not suitable for asynchronous aplications HOT 1
- R503 support for Automatic registration template - AutoEnroll (0x31) & Automatic fingerprint verification - AutoIdentify (0x32)
- Adding fingerprint template transfer functionality to the Adafruit-Fingerprint library HOT 1
- check sum HOT 1
- R558 Fingerprint not picked
- Template Count = 0 when templates exist HOT 5
- Change the Security Level - Code Line HOT 2
- Enroll to first free model HOT 1
- show_fingerprint_templates example writes beyond array bounds HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from adafruit-fingerprint-sensor-library.