Comments (27)
eLvErDe
commented on August 18, 2024
1
Hello,
I uploaded a couple of versions to the repository. Could you show me what happens when using version 2.xx ?
Regards, Adam.
[email protected]:/srv/projects/hwraid/files$ LANG=C apt-cache policy arcconf
arcconf:
Installed: 1:2.02.22404-1
Candidate: 1:2.02.22404-1
Version table:
*** 1:2.02.22404-1 500
500 http://hwraid.le-vert.net/debian jessie/main amd64 Packages
100 /var/lib/dpkg/status
1:1.08.21375-1 500
500 http://hwraid.le-vert.net/debian jessie/main amd64 Packages
1:1.07.21229-1 500
500 http://hwraid.le-vert.net/debian jessie/main amd64 Packages
1:1.05.20942-1 500
500 http://hwraid.le-vert.net/debian jessie/main amd64 Packages
7.31.18856-1 500
500 http://hwraid.le-vert.net/debian jessie/main amd64 Packages
from hwraid.
Nagainos
commented on August 18, 2024
Thank you for giving back arcconf package! Version 2.02 (B22404) working fine.
from hwraid.
eLvErDe
commented on August 18, 2024
@Nagainos Can you also install aacraid-status and send me the output (or errors :D) ?
from hwraid.
Nagainos
commented on August 18, 2024
Yep. That it is:
root@hydra2:/home/nagainos# aacraid-status
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR7805Q | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
-- Disks informations
-- ID | Model | Status
c0uXd0 | SEAGATE ST3600057SS 6SLAV5PX0000N6210KTQ | Online
c0uXd1 | SEAGATE ST3600057SS 6SLATEQK0000N6271HP7 | Online
c0uXd2 | SEAGATE ST3600057SS 6SLAV5MT0000N62803DM | Online
c0uXd3 | SEAGATE ST3600057SS 6SLAV59J0000N6280XBQ | Online
c0uXd4 | SEAGATE ST3600057SS 6SLAV4Z40000N6280WM9 | Raw (Pass Through)
There is at least one disk/array in a NOT OPTIMAL state.
Use "arcconf GETCONFIG [1-9]" to get details.
root@hydra2:/home/nagainos#
from hwraid.
eLvErDe
commented on August 18, 2024
Ok, theres no array displayed. Can you downgrade to version 1.08 ?
Adam
On November 2, 2016 9:29:06 AM GMT+01:00, Nagainos [email protected] wrote:
Yep. That it is:
root@hydra2:/home/nagainos# aacraid-status
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR7805Q | Optimal-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress-- Disks informations
-- ID | Model | Status
c0uXd0 | SEAGATE ST3600057SS 6SLAV5PX0000N6210KTQ | Online
c0uXd1 | SEAGATE ST3600057SS 6SLATEQK0000N6271HP7 | Online
c0uXd2 | SEAGATE ST3600057SS 6SLAV5MT0000N62803DM | Online
c0uXd3 | SEAGATE ST3600057SS 6SLAV59J0000N6280XBQ | Online
c0uXd4 | SEAGATE ST3600057SS 6SLAV4Z40000N6280WM9 | Raw (Pass Through)There is at least one disk/array in a NOT OPTIMAL state.
Use "arcconf GETCONFIG [1-9]" to get details.
root@hydra2:/home/nagainos#You are receiving this because you commented.
Reply to this email directly or view it on GitHub:
#48 (comment)
Envoyé de mon téléphone Android avec K-9 Mail. Excusez la brièveté.
from hwraid.
Nagainos
commented on August 18, 2024
Yes, arcconf downgraded to version 1.08:
root@hydra2:/home/nagainos# aacraid-status
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR7805Q | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
sh: 1: Syntax error: word unexpected (expecting ")")
c0u0 | RAID10 | 1142G | Optimal
-- Disks informations
-- ID | Model | Status
c0u0d0 | SEAGATE ST3600057SS 6SLAV5PX0000N6210KTQ | Online
c0u0d0 | SEAGATE ST3600057SS 6SLATEQK0000N6271HP7 | Online
c0u0d0 | SEAGATE ST3600057SS 6SLAV5MT0000N62803DM | Online
c0u0d0 | SEAGATE ST3600057SS 6SLAV59J0000N6280XBQ | Online
c0uXd0 | SEAGATE ST3600057SS 6SLAV4Z40000N6280WM9 | Raw (Pass Through)
There is at least one disk/array in a NOT OPTIMAL state.
Use "arcconf GETCONFIG [1-9]" to get details.
from hwraid.
eLvErDe
commented on August 18, 2024
Are you really getting the shell error in the middle of the output ?!?!?
Le 2016-11-02 12:46, Nagainos a écrit :
Yes, arcconf downgraded to version 1.08:
root@hydra2:/home/nagainos# aacraid-status
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR7805Q | Optimal-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
sh: 1: Syntax error: word unexpected (expecting ")")
c0u0 | RAID10 | 1142G | Optimal-- Disks informations
-- ID | Model | Status
c0u0d0 | SEAGATE ST3600057SS 6SLAV5PX0000N6210KTQ | Online
c0u0d0 | SEAGATE ST3600057SS 6SLATEQK0000N6271HP7 | Online
c0u0d0 | SEAGATE ST3600057SS 6SLAV5MT0000N62803DM | Online
c0u0d0 | SEAGATE ST3600057SS 6SLAV59J0000N6280XBQ | Online
c0uXd0 | SEAGATE ST3600057SS 6SLAV4Z40000N6280WM9 | Raw (Pass Through)There is at least one disk/array in a NOT OPTIMAL state.
Use "arcconf GETCONFIG [1-9]" to get details.
You are receiving this because you commented.
Reply to this email directly, view it on GitHub [1], or mute the
thread [2].
Links:
[1] #48 (comment)
[2]
https://github.com/notifications/unsubscribe-auth/ABg2RbIDnAjPkPRqgVoLB35m6OlgxOm0ks5q6HgTgaJpZM4JauE7
from hwraid.
Nagainos
commented on August 18, 2024
Yes, that's is right. And I do not getting him after update arcconf utility at version 2.02.22404(but array information is empty).
root@hydra2:/home/nagainos# aacraid-status
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR7805Q | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
-- Disks informations
-- ID | Model | Status
c0uXd0 | SEAGATE ST3600057SS 6SLAV5PX0000N6210KTQ | Online
c0uXd1 | SEAGATE ST3600057SS 6SLATEQK0000N6271HP7 | Online
c0uXd2 | SEAGATE ST3600057SS 6SLAV5MT0000N62803DM | Online
c0uXd3 | SEAGATE ST3600057SS 6SLAV59J0000N6280XBQ | Online
c0uXd4 | SEAGATE ST3600057SS 6SLAV4Z40000N6280WM9 | Raw (Pass Through)
There is at least one disk/array in a NOT OPTIMAL state.
Use "arcconf GETCONFIG [1-9]" to get details.
This behavior is saved(shell error) after update to any of version arcconf, exclude 2.02.22404(we can see him behavior at up) and 7.31.18856(this version doesn't work anytime)
from hwraid.
eLvErDe
commented on August 18, 2024
Can you add "print(cmd)" right after "def getOutput(cmd):" (respect indentation) in /usr/sbin/aacraid-status en re-run with arcconf-1.08 ?
I can hardly understand what triggered this shell message while looking at the code...
from hwraid.
Nagainos
commented on August 18, 2024
Complete.
root@hydra2:/home/nagainos# aacraid-status
"/usr/sbin/arcconf" GETVERSION
-- Controller informations --
-- ID | Model | Status
"/usr/sbin/arcconf" GETCONFIG 1
c0 | Adaptec ASR7805Q | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
"/usr/sbin/arcconf" GETCONFIG 1
"/usr/sbin/arcconf" GETCONFIG 1 LD 0
('"%s" GETSTATUS %s', ('/usr/sbin/arcconf', 1))
sh: 1: Syntax error: word unexpected (expecting ")")
c0u0 | RAID10 | 1142G | Optimal
-- Disks informations
-- ID | Model | Status
"/usr/sbin/arcconf" GETCONFIG 1
"/usr/sbin/arcconf" GETCONFIG 1 PD
"/usr/sbin/arcconf" GETCONFIG 1 LD 0
c0u0d0 | SEAGATE ST3600057SS 6SLAV5PX0000N6210KTQ | Online
"/usr/sbin/arcconf" GETCONFIG 1 LD 0
c0u0d0 | SEAGATE ST3600057SS 6SLATEQK0000N6271HP7 | Online
"/usr/sbin/arcconf" GETCONFIG 1 LD 0
c0u0d0 | SEAGATE ST3600057SS 6SLAV5MT0000N62803DM | Online
"/usr/sbin/arcconf" GETCONFIG 1 LD 0
c0u0d0 | SEAGATE ST3600057SS 6SLAV59J0000N6280XBQ | Online
"/usr/sbin/arcconf" GETCONFIG 1 LD 0
c0uXd0 | SEAGATE ST3600057SS 6SLAV4Z40000N6280WM9 | Raw (Pass Through)
There is at least one disk/array in a NOT OPTIMAL state.
Use "arcconf GETCONFIG [1-9]" to get details.
Python version is 2.7.3
from hwraid.
eLvErDe
commented on August 18, 2024
Wow, that's insane.
Can you replace "print(cmd)" with "print(repr(cmd))" ?
from hwraid.
Nagainos
commented on August 18, 2024
Complete
'"/usr/sbin/arcconf" GETVERSION'
-- Controller informations --
-- ID | Model | Status
'"/usr/sbin/arcconf" GETCONFIG 1'
c0 | Adaptec ASR7805Q | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
'"/usr/sbin/arcconf" GETCONFIG 1'
'"/usr/sbin/arcconf" GETCONFIG 1 LD 0'
('"%s" GETSTATUS %s', ('/usr/sbin/arcconf', 1))
sh: 1: Syntax error: word unexpected (expecting ")")
c0u0 | RAID10 | 1142G | Optimal
-- Disks informations
-- ID | Model | Status
'"/usr/sbin/arcconf" GETCONFIG 1'
'"/usr/sbin/arcconf" GETCONFIG 1 PD'
'"/usr/sbin/arcconf" GETCONFIG 1 LD 0'
c0u0d0 | SEAGATE ST3600057SS 6SLAV5PX0000N6210KTQ | Online
'"/usr/sbin/arcconf" GETCONFIG 1 LD 0'
c0u0d0 | SEAGATE ST3600057SS 6SLATEQK0000N6271HP7 | Online
'"/usr/sbin/arcconf" GETCONFIG 1 LD 0'
c0u0d0 | SEAGATE ST3600057SS 6SLAV5MT0000N62803DM | Online
'"/usr/sbin/arcconf" GETCONFIG 1 LD 0'
c0u0d0 | SEAGATE ST3600057SS 6SLAV59J0000N6280XBQ | Online
'"/usr/sbin/arcconf" GETCONFIG 1 LD 0'
c0uXd0 | SEAGATE ST3600057SS 6SLAV4Z40000N6280WM9 | Raw (Pass Through)
There is at least one disk/array in a NOT OPTIMAL state.
Use "arcconf GETCONFIG [1-9]" to get details.
from hwraid.
eLvErDe
commented on August 18, 2024
Are you sure you did not messed up the script ?
I can't understand why you get this being printed: ('"%s" GETSTATUS %s', ('/usr/sbin/arcconf', 1))
If running Debian. can you give apt-get install --reinstall aacraid-status a try ?
from hwraid.
Nagainos
commented on August 18, 2024
Are you sure you did not messed up the script ?
How I can corrup that script momentarily after install? What I can do to that? I can try to make something, but I do not many action about this python script.
If running Debian. can you give apt-get install --reinstall aacraid-status a try ?
Package reinstalled and problem is persist.
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR7805Q | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
sh: 1: Syntax error: word unexpected (expecting ")")
c0u0 | RAID10 | 1142G | Optimal
-- Disks informations
-- ID | Model | Status
c0u0d0 | SEAGATE ST3600057SS 6SLAV5PX0000N6210KTQ | Online
c0u0d0 | SEAGATE ST3600057SS 6SLATEQK0000N6271HP7 | Online
c0u0d0 | SEAGATE ST3600057SS 6SLAV5MT0000N62803DM | Online
c0u0d0 | SEAGATE ST3600057SS 6SLAV59J0000N6280XBQ | Online
c0uXd0 | SEAGATE ST3600057SS 6SLAV4Z40000N6280WM9 | Raw (Pass Through)
There is at least one disk/array in a NOT OPTIMAL state.
Use "arcconf GETCONFIG [1-9]" to get details.
Before reinstall package aacraid-status I'm try to install arcconf=1:2.02.22404-1 and run aacraid-status with print(repr(cmd)) and I can't see row ('"%s" GETSTATUS %s', ('/usr/sbin/arcconf', 1))
root@hydra2:/home/nagainos# aacraid-status
'"/usr/sbin/arcconf" GETVERSION'
-- Controller informations --
-- ID | Model | Status
'"/usr/sbin/arcconf" GETCONFIG 1'
c0 | Adaptec ASR7805Q | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
'"/usr/sbin/arcconf" GETCONFIG 1'
-- Disks informations
-- ID | Model | Status
'"/usr/sbin/arcconf" GETCONFIG 1'
'"/usr/sbin/arcconf" GETCONFIG 1 PD'
c0uXd0 | SEAGATE ST3600057SS 6SLAV5PX0000N6210KTQ | Online
c0uXd1 | SEAGATE ST3600057SS 6SLATEQK0000N6271HP7 | Online
c0uXd2 | SEAGATE ST3600057SS 6SLAV5MT0000N62803DM | Online
c0uXd3 | SEAGATE ST3600057SS 6SLAV59J0000N6280XBQ | Online
c0uXd4 | SEAGATE ST3600057SS 6SLAV4Z40000N6280WM9 | Raw (Pass Through)
There is at least one disk/array in a NOT OPTIMAL state.
Use "arcconf GETCONFIG [1-9]" to get details.
It's a strange situation.
At now I get back all packages and problem is persist.
apt-get -y install --reinstall aacraid-status
apt-get -y install arcconf=1:1.08.21375-1 --reinstall --force-yes
from hwraid.
eLvErDe
commented on August 18, 2024
Can you send /usr/sbin/arcconf" GETCONFIG 1 LD 0 output with 1.08 and 2.02 ? I'll forget the sh error as I have absolutely no idea what the issue could be. Let's focus on getting the wrapper working with 2.x ;-)
from hwraid.
Nagainos
commented on August 18, 2024
I send details to e-mail about how work arcconf under strace. I found some file path where mabye exist debug logs and if I create him at disk arcconf write some infos about work him. This files from my system I send to you email, but I'm not sure what any people can analyze logs without source codes of arcconf utility.
root@hydra2:/var/cache/apt/archives# arcconf | head
| UCLI | Adaptec by PMC uniform command line interface
| UCLI | Version 7.31 (B18856)
| UCLI | (C) Adaptec by PMC 2003-2011
| UCLI | All Rights Reserved
root@hydra2:/var/cache/apt/archives# arcconf GETCONFIG 1
Controllers found: 1
----------------------------------------------------------------------
Controller information
----------------------------------------------------------------------
Controller Status : Inaccessible
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
No logical devices configured
----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
Command completed successfully.
root@hydra2:/home/srvadm# ./arcconf | head
| UCLI | Adaptec by PMC uniform command line interface
| UCLI | Version 1.08 (B21375)
| UCLI | (C) Adaptec by PMCS 2003-2015
| UCLI | All Rights Reserved
root@hydra2:/home/srvadm# ./arcconf GETCONFIG 1
Controllers found: 1
----------------------------------------------------------------------
Controller information
----------------------------------------------------------------------
Controller Status : Optimal
Controller Mode : RAID (Expose RAW)
Controller Cache Preservation : Disabled
Channel description : SAS/SATA
Controller Model : Adaptec ASR7805Q
Controller Serial Number : 6D0663406EE
Controller World Wide Name : 50000D1701138400
Physical Slot : 4
Temperature : 86 C/ 186 F (Normal)
Installed memory : 1024 MB
Copyback : Disabled
Background consistency check : Enabled
Background consistency check period : 0
Automatic Failover : Enabled
Global task priority : High
Performance Mode : Default/Dynamic
Host bus type : PCIe
Host bus speed : 8000 MHz
Host bus link width : 8 bit(s)/link(s)
Stayawake period : Disabled
Spinup limit internal drives : 0
Spinup limit external drives : 0
Defunct disk drive count : 0
Logical devices/Failed/Degraded : 1/0/0
MaxCache flush and fetch rate : 0
MaxCache Read, Write Balance Factor : 3,1
MaxCache Dirty Page Threshold : 0
NCQ status : Enabled
Statistics data collection mode : Disabled
--------------------------------------------------------
Controller Version Information
--------------------------------------------------------
BIOS : 7.5-0 (32106)
Firmware : 7.5-0 (32106)
Driver : 1.2-1 (50667)
Boot Flash : 7.5-0 (32106)
--------------------------------------------------------
Controller Cache Backup Unit Information
--------------------------------------------------------
Overall Backup Unit Status : Ready
Backup Unit Type : AFM-700/700LP
Non-Volatile Storage Status : Ready [132/1839]
Supercap Status : Ready
-----------------------------------
Supercap Information
-----------------------------------
Current Temperature : 28 deg C
Threshold Temperature : 51 deg C
Life-time Temperature Recorded
(Min/Max) : 17 deg C/ 34 deg C
Voltage(Present/Max) : 4955 mV/ 5302 mV
Life-time Max Voltage Recorded : 5432 mV
Current Drawn(Present/Max) : -12 mA/ 560 mA
Health : 100 percent
Charge Level : 100 percent
Estimated Life-time : 5 Years, 0 Month
Serial Number : 6A066D3F7D3
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name : Hydra2
Block Size of member drives : 512 Bytes
RAID level : 10
Unique Identifier : 1F0581A7
Status of logical device : Optimal
Size : 1142774 MB
Parity space : 1142784 MB
Stripe-unit size : 512 KB
Read-cache setting : Enabled
Read-cache status : On
Write-cache setting : Enabled
Write-cache status : On
MaxCache read cache setting : Enabled
MaxCache read cache status : Off
MaxCache write cache setting : Disabled
MaxCache write cache status : Off
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Group 0, Segment 0 : Present (Controller:1,Enclosure:0,Slot:0) 6SLAV5PX0000N6210KTQ
Group 0, Segment 1 : Present (Controller:1,Enclosure:0,Slot:1) 6SLATEQK0000N6271HP7
Group 1, Segment 0 : Present (Controller:1,Enclosure:0,Slot:4) 6SLAV5MT0000N62803DM
Group 1, Segment 1 : Present (Controller:1,Enclosure:0,Slot:5) 6SLAV59J0000N6280XBQ
----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
Device #0
Device is a Hard drive
State : Online
Block Size : 512 Bytes
Supported : Yes
Transfer Speed : SAS 6.0 Gb/s
Reported Channel,Device(T:L) : 0,0(0:0)
Reported Location : Enclosure 0, Slot 0
Reported ESD(T:L) : 2,0(0:0)
Vendor : SEAGATE
Model : ST3600057SS
Firmware : 000B
Serial number : 6SLAV5PX0000N6210KTQ [63/1839]
World-wide name : 5000C500963BD1F4
Reserved Size : 956312 KB
Used Size : 571392 MB
Unused Size : 64 KB
Total Size : 572325 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
Device #1
Device is a Hard drive
State : Online
Block Size : 512 Bytes
Supported : Yes
Transfer Speed : SAS 6.0 Gb/s
Reported Channel,Device(T:L) : 0,1(1:0)
Reported Location : Enclosure 0, Slot 1
Reported ESD(T:L) : 2,0(0:0)
Vendor : SEAGATE
Model : ST3600057SS
Firmware : 000B
Serial number : 6SLATEQK0000N6271HP7
World-wide name : 5000C5009621EF60
Reserved Size : 956312 KB
Used Size : 571392 MB
Unused Size : 64 KB
Total Size : 572325 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
Device #2
Device is a Hard drive
State : Online
Block Size : 512 Bytes
Supported : Yes
Transfer Speed : SAS 6.0 Gb/s
Reported Channel,Device(T:L) : 0,4(4:0)
Reported Location : Enclosure 0, Slot 4
Reported ESD(T:L) : 2,0(0:0)
Vendor : SEAGATE
Model : ST3600057SS
Firmware : 000B
Serial number : 6SLAV5MT0000N62803DM
World-wide name : 5000C500963BF804
Reserved Size : 956312 KB
Used Size : 571392 MB
Unused Size : 64 KB
Total Size : 572325 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
Device #3
Device is a Hard drive
State : Online
Block Size : 512 Bytes
Supported : Yes
Transfer Speed : SAS 6.0 Gb/s
Reported Channel,Device(T:L) : 0,5(5:0)
Reported Location : Enclosure 0, Slot 5
Reported ESD(T:L) : 2,0(0:0)
Vendor : SEAGATE
Model : ST3600057SS
Firmware : 000B
Serial number : 6SLAV59J0000N6280XBQ
World-wide name : 5000C500963C0F58
Reserved Size : 956312 KB
Used Size : 571392 MB
Unused Size : 64 KB
Total Size : 572325 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
Device #4
Device is a Hard drive
State : Raw (Pass Through)
Block Size : 512 Bytes
Supported : Yes
Transfer Speed : SAS 6.0 Gb/s
Reported Channel,Device(T:L) : 0,6(6:0)
Reported Location : Enclosure 0, Slot 6
Reported ESD(T:L) : 2,0(0:0)
Vendor : SEAGATE
Model : ST3600057SS
Firmware : 000B
Serial number : 6SLAV4Z40000N6280WM9
World-wide name : 5000C500963C42F0
Reserved Size : 0 KB
Used Size : 0 MB
Unused Size : 572325 MB
Total Size : 572325 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
Device #5
Device is an Enclosure services device
Reported Channel,Device(T:L) : 2,0(0:0)
Enclosure ID : 0
Type : SES2
Vendor : ADAPTEC
Model : Virtual SGPIO
Firmware : 1
Status of Enclosure services device
Speaker status : Not available
----------------------------------------------------------------------
MaxCache 3.0 information
----------------------------------------------------------------------
No Maxcache 3.0 found
Command completed successfully.
from hwraid.
iotaka
commented on August 18, 2024
Hello Adam,
at the moment I don't have available the series 8 machine, this is the output on a old 5 series:
# aacraid-status
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec 5805 | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
-- Disks informations
-- ID | Model | Status
c0uXd0 | Hitachi HUA722010CLA330 JPW9K0HZ21E7UL | Online
c0uXd1 | Hitachi HUA722010CLA330 JPW9K0HZ21EBBL | Online
c0uXd2 | Hitachi HUA722010CLA330 JPW9K0HZ21E0HL | Online
c0uXd3 | Hitachi HUA722010CLA330 JPW9K0HZ216PYL | Online
c0uXd4 | Hitachi HUA722010CLA330 JPW9K0HZ216D0L | Online
c0uXd5 | Hitachi HUA722010CLA330 JPW9K0HZ216NJL | Online
Version 2.02 (B22404)
# /usr/sbin/arcconf GETCONFIG 1 LD 0
Controllers found: 1
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical Device number 0
Logical Device name : PX
Block Size of member drives : 512 Bytes
RAID level : 10
Unique Identifier : 994687AC
Status of Logical Device : Optimal
Additional details : Quick initialized
Size : 2860022 MB
Parity space : 2860032 MB
Stripe-unit size : 256 KB
Interface Type : Serial ATA
Device Type : HDD
Read-cache setting : Enabled
Read-cache status : On
Write-cache setting : On when protected by battery/ZMM
Write-cache status : On
maxCache read cache setting : Enabled
maxCache read cache status : Off
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical Device segment information
--------------------------------------------------------
Group 0, Segment 0 : Present (953869MB, SATA, HDD, Connector:1, Device:0) JPW9K0HZ216D0L
Group 0, Segment 1 : Present (953869MB, SATA, HDD, Connector:1, Device:1) JPW9K0HZ216NJL
Group 1, Segment 0 : Present (953869MB, SATA, HDD, Enclosure:0, Slot:0) JPW9K0HZ21E7UL
Group 1, Segment 1 : Present (953869MB, SATA, HDD, Enclosure:0, Slot:1) JPW9K0HZ21EBBL
Group 2, Segment 0 : Present (953869MB, SATA, HDD, Enclosure:0, Slot:2) JPW9K0HZ21E0HL
Group 2, Segment 1 : Present (953869MB, SATA, HDD, Enclosure:0, Slot:3) JPW9K0HZ216PYL
Command completed successfully.
.
Version 1.08 (B21375)
# /usr/sbin/arcconf GETCONFIG 1 LD 0
Controllers found: 1
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name : PX
Block Size of member drives : 512 Bytes
RAID level : 10
Unique Identifier : 994687AC
Status of logical device : Optimal
Additional details : Quick initialized
Size : 2860022 MB
Parity space : 2860032 MB
Stripe-unit size : 256 KB
Read-cache setting : Enabled
Read-cache status : On
Write-cache setting : On when protected by battery/ZMM
Write-cache status : On
maxCache read cache setting : Enabled
maxCache read cache status : Off
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Group 0, Segment 0 : Present (Controller:1,Connector:1,Device:0) JPW9K0HZ216D0L
Group 0, Segment 1 : Present (Controller:1,Connector:1,Device:1) JPW9K0HZ216NJL
Group 1, Segment 0 : Present (Controller:1,Enclosure:0,Slot:0) JPW9K0HZ21E7UL
Group 1, Segment 1 : Present (Controller:1,Enclosure:0,Slot:1) JPW9K0HZ21EBBL
Group 2, Segment 0 : Present (Controller:1,Enclosure:0,Slot:2) JPW9K0HZ21E0HL
Group 2, Segment 1 : Present (Controller:1,Enclosure:0,Slot:3) JPW9K0HZ216PYL
Command completed successfully.
Thank you for the support.
from hwraid.
eLvErDe
commented on August 18, 2024
Thanks, that helped a lot. I pushed a new aacraid-status wrapper according to what I saw here. Can you give a try with different arrconf version and let me know if it's working ?
Also I'd love seeing more output on other gen controller.
Best regards, Adam.
from hwraid.
eLvErDe
commented on August 18, 2024
Hello @iotaka,
Day off today ? Don't forget to check this on monday, you're my only hope to fix aacraid-status at the moment,
Thanks, Adam.
from hwraid.
iotaka
commented on August 18, 2024
Hello Adam @eLvErDe ,
busy at work! Sorry for the delay. This is a whezzey not a jessie with a series 6 controller:
# aacraid-status
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec 6805 | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
-- Disks informations
-- ID | Model | Status
c0uXd0 | Hitachi HUA723020ALA640 MK0251YGHNTE2A | Online
c0uXd1 | Hitachi HUA723020ALA640 MK0173YFHMPPAC | Online
c0uXd2 | Hitachi HUA723020ALA640 MK0251YGHNYHAA | Online
c0uXd3 | Hitachi HUA723020ALA640 MK0251YGHNRP2A | Online
Version 2.02 (B22404)
# /usr/sbin/arcconf GETCONFIG 1 LD 0
Controllers found: 1
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical Device number 0
Logical Device name : Raid 5
Block Size of member drives : 512 Bytes
RAID level : 5
Unique Identifier : 728A9B2B
Status of Logical Device : Optimal
Additional details : Initialized with Build/Clear
Size : 102389 MB
Parity space : 34133 MB
Stripe-unit size : 256 KB
Interface Type : Serial ATA
Device Type : HDD
Read-cache setting : Enabled
Read-cache status : On
Write-cache setting : On when protected by battery/ZMM
Write-cache status : On
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical Device segment information
--------------------------------------------------------
Segment 0 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:0) MK0251YGHNTE2A
Segment 1 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:1) MK0173YFHMPPAC
Segment 2 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:2) MK0251YGHNYHAA
Segment 3 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:3) MK0251YGHNRP2A
Command completed successfully.
.
Version 1.08 (B21375)
# /usr/sbin/arcconf GETCONFIG 1 LD 0
Controllers found: 1
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name : Raid 5
Block Size of member drives : 512 Bytes
RAID level : 5
Unique Identifier : 728A9B2B
Status of logical device : Optimal
Additional details : Initialized with Build/Clear
Size : 102389 MB
Parity space : 34133 MB
Stripe-unit size : 256 KB
Read-cache setting : Enabled
Read-cache status : On
Write-cache setting : On when protected by battery/ZMM
Write-cache status : On
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Segment 0 : Present (Controller:1,Enclosure:0,Slot:0) MK0251YGHNTE2A
Segment 1 : Present (Controller:1,Enclosure:0,Slot:1) MK0173YFHMPPAC
Segment 2 : Present (Controller:1,Enclosure:0,Slot:2) MK0251YGHNYHAA
Segment 3 : Present (Controller:1,Enclosure:0,Slot:3) MK0251YGHNRP2A
Command completed successfully.
Cheers
from hwraid.
iotaka
commented on August 18, 2024
Hello Adam @eLvErDe
i found finally a 8 series controller :)
# aacraid-status
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR8805 | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
-- Disks informations
-- ID | Model | Status
c0uXd0 | ATA ST2000NM0033-9ZM Z1X51Q2Z | Online
c0uXd1 | ATA ST2000NM0033-9ZM Z1X54373 | Online
c0uXd2 | ATA ST2000NM0033-9ZM Z1X543XL | Online
c0uXd3 | ATA ST2000NM0033-9ZM Z1X544BL | Online
c0uXd4 | ATA ST2000NM0033-9ZM Z1X543A7 | Online
c0uXd5 | ATA ST2000NM0033-9ZM Z1X54EGF | Online
Version 2.02 (B22404)
# /usr/sbin/arcconf GETCONFIG 1 LD 0
Controllers found: 1
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical Device number 0
Logical Device name : OS
Block Size of member drives : 512 Bytes
RAID level : 10
Unique Identifier : 4021C42D
Status of Logical Device : Optimal
Additional details : Quick initialized
Size : 102389 MB
Parity space : 102399 MB
Stripe-unit size : 256 KB
Interface Type : Serial ATA
Device Type : HDD
Read-cache setting : Enabled
Read-cache status : On
Write-cache setting : On when protected by battery/ZMM
Write-cache status : On
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical Device segment information
--------------------------------------------------------
Group 0, Segment 0 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:0) Z1X51Q2Z
Group 0, Segment 1 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:1) Z1X54373
Group 1, Segment 0 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:2) Z1X543XL
Group 1, Segment 1 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:3) Z1X544BL
Group 2, Segment 0 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:4) Z1X543A7
Group 2, Segment 1 : Present (1907729MB, SATA, HDD, Enclosure:0, Slot:5) Z1X54EGF
Command completed successfully.
.
ersion 1.08 (B21375)
# /usr/sbin/arcconf GETCONFIG 1 LD 0
Controllers found: 1
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name : OS
Block Size of member drives : 512 Bytes
RAID level : 10
Unique Identifier : 4021C42D
Status of logical device : Optimal
Additional details : Quick initialized
Size : 102389 MB
Parity space : 102399 MB
Stripe-unit size : 256 KB
Read-cache setting : Enabled
Read-cache status : On
Write-cache setting : On when protected by battery/ZMM
Write-cache status : On
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Group 0, Segment 0 : Present (Controller:1,Enclosure:0,Slot:0) Z1X51Q2Z
Group 0, Segment 1 : Present (Controller:1,Enclosure:0,Slot:1) Z1X54373
Group 1, Segment 0 : Present (Controller:1,Enclosure:0,Slot:2) Z1X543XL
Group 1, Segment 1 : Present (Controller:1,Enclosure:0,Slot:3) Z1X544BL
Group 2, Segment 0 : Present (Controller:1,Enclosure:0,Slot:4) Z1X543A7
Group 2, Segment 1 : Present (Controller:1,Enclosure:0,Slot:5) Z1X54EGF
Command completed successfully.
Cheers
from hwraid.
eLvErDe
commented on August 18, 2024
Hello,
I just updated the aacraid-status script, thanks for the output examples. Can you give a try again ?
Adam.
from hwraid.
iotaka
commented on August 18, 2024
I performed an apt update, but I still see the version 0.21 used for the last message
apt-cache policy aacraid-status
aacraid-status:
Installed: 0.21
Candidate: 0.21
from hwraid.
eLvErDe
commented on August 18, 2024
Hello,
Actually Im waiting for your feedback before releasing ;-)
Can you get latest version from github directly ?
Regards, Adam
from hwraid.
iotaka
commented on August 18, 2024
Hello Adam @eLvErDe
Using this one:
https://raw.githubusercontent.com/eLvErDe/hwraid/master/wrapper-scripts/aacraid-status
# ./aatest
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR8805 | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
Traceback (most recent call last):
File "./aatest", line 261, in <module>
arrayids = returnArrayIds(output)
File "./aatest", line 68, in returnArrayIds
ids.append(re.sub(r'^Logical [Dd]evice number', line).strip())
TypeError: sub() takes at least 3 arguments (2 given)
Cheers
from hwraid.
eLvErDe
commented on August 18, 2024
Hello,
I just committed a fix, can you try again ?
Thanks
Le 2016-11-17 09:31, iotaka a écrit :
Hello Adam @eLvErDe [1]
Using this one:
https://raw.githubusercontent.com/eLvErDe/hwraid/master/wrapper-scripts/aacraid-status./aatest
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR8805 | Optimal-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
Traceback (most recent call last):
File "./aatest", line 261, in
arrayids = returnArrayIds(output)
File "./aatest", line 68, in returnArrayIds
ids.append(re.sub(r'^Logical [Dd]evice number', line).strip())
TypeError: sub() takes at least 3 arguments (2 given)Cheers
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub [2], or mute the
thread [3].
Links:
[1] https://github.com/eLvErDe
[2] #48 (comment)
[3]
https://github.com/notifications/unsubscribe-auth/ABg2RfX7gsGxNsVLBEym0_dvhhGLRq_kks5q_BD0gaJpZM4JauE7
from hwraid.
iotaka
commented on August 18, 2024
Hello Adam @eLvErDe
# ./aatest2
-- Controller informations --
-- ID | Model | Status
c0 | Adaptec ASR8805 | Optimal
-- Arrays informations --
-- ID | Type | Size | Status | Task | Progress
sh: 1: Syntax error: word unexpected (expecting ")")
c0u0 | RAID10 | 3809G | Optimal
-- Disks informations
-- ID | Model | Status
c0u0d0 | ATA HGST HUS724020AL PN1134P5G5989W | Online
c0u0d0 | ATA HGST HUS724020AL PN1134P5G5D0MW | Online
c0u0d0 | ATA HGST HUS724020AL PN1134P5G5A98W | Online
c0u0d0 | ATA HGST HUS724020AL PN1134P5G598PW | Online
Cheers
from hwraid.
Related Issues (20)
- Repository for Debian bullseye HOT 10
- Debian package versions: stretch beats buster HOT 3
- UnicodeDecodeError: 'utf-8' codec can't decode bytes in position 146-147: invalid continuation byte HOT 5
- https://hwraid.le-vert.net/debian/hwraid.le-vert.net.gpg.key expired HOT 4
- Missing packages - Debian 11 (bullseye) HOT 8
- LSI/Dell PERC H750 compatibility HOT 2
- LSI 3916 megaraid_sas problem HOT 2
- megaclisas-status difficulty processing megacli output HOT 1
- Ubuntu 22.04 Support
- Apt Warns HOT 1
- megacli and megaclisas-status kill conttroller's FW HOT 16
- Error opening terminal: xterm?
- Repository for Debian Bookworm HOT 12
- slight mishap
- H700 bricked (Dell T710) HOT 1
- Missing packages - Debian 12 (bookworm) HOT 10
- Debian bullseye, repository is now missing HOT 4
- megagli not working completely on debian 12 (Segmentation fault)
- hpacucli is not available for bullseye but the package from buster works
- SyntaxWarning: invalid escape sequence '\(' HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from hwraid.