Comments (18)
from glibc_ddwrt.
from glibc_ddwrt.
About Rate I will try set frequency manually to check.
About freeze I will try get log if freeze again.
But for now I get again the problem of "not have internet".
I checked my WAN and is in DHCP Mode and when I click in DHCP Renew I get this output:
When I restart DIR-3040 all is OK again:
from glibc_ddwrt.
from glibc_ddwrt.
Hmmm but the problem not is internet or DNS.
I'm using DIR-3040 connected by WAN to my primary router, so the WAN IP received it's internal on my network.
DIR-3040 is losing functionality in WAN port.
from glibc_ddwrt.
from glibc_ddwrt.
from glibc_ddwrt.
Yes, stock is OK I'm use as the same way before change and used a mikrotik too as the same way.
When problem not occurs, the DHCP Release and DHCP Renew works 100% on WAN using this config.
I never see this problem too.
from glibc_ddwrt.
that lease time looks wrong though
with my WAN connected to the modem, i am always getting a lease time.
sounds to me you need to configure or figure out why that lease time is zero. it should never be zero because that's when it should be renewed.
i bet the stock fw did something to address this. you're the first person to report this problem.
from glibc_ddwrt.
also, is your dhcp start configured to 3?
i think by default the dhcp start value is much higher (64?)
from glibc_ddwrt.
No, my DHCP on router internet start from 2, but I'm using mikrotik on 2.
My planing is replace mikrotik by dir-3040.
About release time probably is because in internet router i marked this dir-3040 to not change IP.
Normally people use provider router as bridge and the private router as a WAN - PPPoE.
In my cause I only put in provider router my internal router in DMZ mode.
from glibc_ddwrt.
I think i found the problem.
I get the same problem, so I find, copy command line and kill udhcpc.
After that I run again udhcpc with the command line and WAN back to work.
The problem now is know why stoped working and how fix.
from glibc_ddwrt.
it may have to do with syntax differences in the bash script /etc/cidrroute.sh between busybox and glibc-based bash, but i cna't say for sure.
but i do know this file is called when it moves from an unbound to a bound state. try to play with that script and let me know, because it is probably the only possible issue.
from glibc_ddwrt.
Thanks I will try.
I noted that when remove WAN cable the DD-WRT no detect or not update status :D
You have command to disable LED?
I want create a CRON tab to disable LED after 1h
from glibc_ddwrt.
no, it only turns off if you turn off the radios. you can turn of all 3 radios by holding the button at the front.
i am not going to add that feature either, lol. sorry
from glibc_ddwrt.
Hi @i3roly, I still have problem with WAN Port :/
I already know the port and cable is OK.
I tested WAN with Static IP and after a while stops too, no error no log and DD-WRT show IP like nothing have changed and it's the same when WAN in in DHCP Mode.
I noticed that the WAN port is as vlan2, can you activate the Setup - VLANs in DD-WRT?
Very thanks
from glibc_ddwrt.
from glibc_ddwrt.
Ok, but you can enable Setup -VLANs?
For now I changed WAN to eth3 to test.
from glibc_ddwrt.
Related Issues (20)
- DIR-3040 Firmware not update HOT 28
- Trouble connecting to wifi on some devices & LED error HOT 14
- WPA2 Enterprise HOT 58
- DIR-3040 router username/password outright not working, and GUI access not disabling HOT 12
- port forwarding HOT 8
- GUI Webpage 404 HOT 5
- OPKG Install Script HOT 1
- vap HOT 2
- Wifi physical interfaces disappears in latest build HOT 3
- wifi struggling on some devices HOT 11
- WLAN disconnecting from switch HOT 10
- Sir I am using 2640 HOT 5
- Router times out on few menu's DIR-882 HOT 22
- Assistance in Installing this version.
- SAMBA USB File sharing not working in 47458M D-Link 266O HOT 6
- Unable to update DIR-878 after 47495 release. HOT 12
- Multi User Beamforming HOT 9
- DIR-882: WiFi roaming support? HOT 4
- virtual interfaces HOT 7
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from glibc_ddwrt.