Compatibility RF95 about lorawangateway

[JaapBraam]

Do you get 'Unknown radio: 9' each time you restart your gateway or does it vary?

If you always get 'Unknown radio: 9' the RF95 module it probably does not contain a SX1276. (I use RFM95 modules wich work great)

If the reported radio varies you should check your SPI connections.

[BoelD]

Tried a couple of times and it's always Unkown Radio 9. I paid a closer look and see that the module I am using is actually a RF 96. It was recognized by the Raspberri Pi gateway I previously used as an SX1272/1276 module. Hence the mistake.

I have a couple of other radio modules that I collected over time and see if I can get it wo work with one of those.

[Rubensen]

Hi Mine is also using this chip, RF96, and is working and connected to TTN. Rubens

…

On 1 Jun 2017 13:46, "DavidBoelee" ***@***.***> wrote: Tried a couple of times and it's always Unkown Radio 9. I paid a closer look and see that the module I am using is actually a RF 96. It was recognized by the Raspberri Pi gateway I previously used as an SX1272/126 module. Hence the mistake. I have a couple of other radio modules that I collected over time and see if I can get it wo work with one of those. — You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub <#34 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/AOXCOZf2-0Xmh6yKALeNJYq-hlFBQywvks5r_qSegaJpZM4Ns0jr> .

[BoelD]

Ok, I wired it up with another RF96 module that had in my drawer and now it's working fine. Couldn't resist trying it with a SX1272 that I had as well, but that's not working (as expected).

Thanks for your help!

[BoelD]

I must add that it's working with ABP, I can't get OTAA to work yet. I dived into the other issues regarding OTAA and was wondering whether there is some more documentation available about the settings of the gateway that I can tweak to make it work?

[Rubensen]

For me only ABP works too. My gateway is working more than a month right now, and can been seen at ttnmapper.org Denmark, Ballerup. All mesurements made with fixed SF7. Nice work JaapBraam! Thanks. Rubens Em sex, 2 de jun de 2017 às 11:44, DavidBoelee <[email protected]> escreveu:

…

I must add that it's working with ABP, I can't get OTAA to work yet. I dived into the other issues regarding OTAA and was wondering whether there is some more documentation available about the settings of the gateway that I can tweak to make it work? — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#34 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/AOXCOc-0gImf3Kw7nmava5LyC972eE7mks5r_9mKgaJpZM4Ns0jr> .

[JaapBraam]

I had some troubles with OTAA too: it was difficult to have a LMIC based node join successfully. It turned out that by specifying a MAX_CLOCK_ERROR of 5% on the node it joined quite reliable.

[Rubensen]

I´m waiting 10 pieces of RFM95W (aka RF96) to test OTAA again, with the max_clock_error change. I think this cheap ardunish pro mini modules uses ressonators instead of crystals, witch could be the cause of the problem. As I receive 10 prominis today, I will create delays of 100ms and 1s and verify with a scope how precise they are. Thanks for the suggetion JaapBraam. Rubens

…

On Fri, Jun 2, 2017 at 2:57 PM, Jaap Braam ***@***.***> wrote: I had some troubles with OTAA too: it was difficult to have a LMIC based node join successfully. It turned out that by specifying a MAX_CLOCK_ERROR of 5% on the node it joined quite reliable. — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#34 (comment)>, or mute the thread <https://github.com/notifications/unsubscribe-auth/AOXCOVIp4MkgDSzmfZSGJCLQbX_9dkXLks5sAAaygaJpZM4Ns0jr> .