OpenKNX Common is a library meant to be used once in every OpenKNX Device firmware.
The main functions are:
- setup and calling the knx stack
- setup and calling of the OpenKNX Modules
- flash handling for persistent data of the OpenKNX Modules
It is designed for usage with the headerfile generated by OpenKNXproducer, which provides the necessary defines in knxprod.h:
MAIN_OpenKnxId
MAIN_ApplicationNumber
MAIN_ApplicationVersion
# optional (delivered by OAM-LogicModule)
LOG_StartupDelayBase
ParamLOG_StartupDelayTimeMS
LOG_HeartbeatDelayBase
KoLOG_Heartbeat
ParamLOG_HeartbeatDelayTimeMS
| ARCH | info |
|---|---|
| RP2040 | the reference platform with full support (including dual core support) |
| SAMD21 | obsolete but still supported. no hw should be developed on this anymore |
| ESP32 | experimental |
To configure the Hardware-Setup use the following defines in hardware.h
SAVE_INTERRUPT_PIN
INFO_LED_PIN
PROG_BUTTON_PIN
PROG_LED_PIN_ACTIVE_ON
PROG_LED_PIN
KNX_UART_RX_PIN
KNX_UART_TX_PIN
| define | default | unit | function |
|---|---|---|---|
| OPENKNX_RECOVERY_TIME | 6000 | ms | hold prog button to erase knx and openknx data (not firmware or filesystem). Turn off with 0 |
| OPENKNX_DUALCORE | build with dualcore support (only on RP2040) | ||
| OPENKNX_WATCHDOG | compile with watchdog (use only for releases. debugger not working with active watchdog) | ||
| OPENKNX_WATCHDOG_MAX_PERIOD | 16384 | ms | the timeout period of watchdog |
| OPENKNX_NO_BOOT_PULSATING | Turn off the pulsating LED during the boot phase. (Only necessary for specific hardware where the LED cannot be controlled via PWM). | ||
| OPENKNX_MAX_MODULES | 9 | ||
| OPENKNX_LEDEFFECT_PULSE_FREQ | 1000 | ms | |
| OPENKNX_LEDEFFECT_BLINK_FREQ | 1000 | ms | |
| OPENKNX_WAIT_FOR_SERIAL | 2000 | ms | wait at startup until SERIAL_DEBUG is connected. (optional with timeout - in devmode use high values like 20000 - 0 will disable waiting) Not supported on ESP32 |
| OPENKNX_HEARTBEAT | 1000 | ms | enable heartbeat mode (optional with with specific failure time) |
| OPENKNX_HEARTBEAT_PRIO | 3000 | ms | enable heartbeat prio mode (optional with with specific failure time) |
| OPENKNX_HEARTBEAT_FREQ | 200 | ms | |
| OPENKNX_HEARTBEAT_PRIO_ON_FREQ | 200 | ms | |
| OPENKNX_HEARTBEAT_PRIO_OFF_FREQ | 1000 | ms | |
| OPENKNX_MAX_LOOPTIME | 4000 | µs | how much time is the loop allowed to consume. (soft limit) |
| OPENKNX_LOOPTIME_WARNING | 7 | ms | issue a warning if the loop has lasted X ms or longer longer. |
| OPENKNX_LOOPTIME_WARNING_INTERVAL | 1000 | ms | how often the warning may be issued in the console |
| OPENKNX_RUNTIME_STAT | Integrate Collection of Runtime-Statistics for core0. | ||
| OPENKNX_RUNTIME_STAT_BUCKETN | 16 | the number of histogram buckets for Runtime-Statistics | |
| OPENKNX_RUNTIME_STAT_BUCKETS | default set | µs | The upper (included) limits of histogram bucket, without last bucket as this will be limited by data-type only. Must be a comma-separated list with OPENKNX_RUNTIME_STAT_BUCKETN-1 entries |
| OPENKNX_DEBUG | Enable debug mode | ||
| OPENKNX_TRACE1..5 | Enable debug mode + tracing. to see trace logs, they must match one of the 5 regex filters. | ||
| OPENKNX_RTT | Enable RTT Mode (Disable USB Serial output) + Increase BUFFER_SIZE_UP to 10240! | ||
| BUFFER_SIZE_UP | 1024 | Bytes | Using by Segger RTT |
You can enable a debug heartbeat to see if a loop is stuck. The progLed (for loop) and infoLed (for loop1) will blinking if the loop hangs.
In the prio mode the leds blinking (OPENKNX_HEARTBEAT_PRIO_OFF_FREQ) and stop as soon as the relevant loop hangs.
If programing mode is active, the progLed will blink faster (OPENKNX_HEARTBEAT_PRIO_ON_FREQ).
So, if the device is NOT blinking, anything is wrong.
