austilphukir / deye-inverter-mqtt

Reads Deye solar inverter metrics and posts them over mqtt

Deye solar inverter MQTT bridge

Reads Deye solar inverter metrics using Modbus over TCP and publishes them over MQTT.

Tested with:

• Deye SUN-4K-G05 and Logger S/N 23xxxxxxxx
• Deye SUN1300G3 and Logger S/N 41xxxxxxxx
• Deye SUN600G3 and Device S/N 41xxxxxxxx

Supported metrics

The meaning of certain registers depends on the inverter type. For example, string inverters use registers 0x46 - 0x4e to report AC phase voltage/current. On the other hand, micro inverters use this same registers to report pv1-pv4 cumulative energy. Generally there are three types of inverters documented in the specification: string, micro and hybrid. In the table below you can see, that the metrics are assigned to specific groups. Empty value indicates a general purpose metric, that is available in all type of inverters. You should specify the set of groups that is appropriate for your inverter in DEYE_METRIC_GROUPS environment variable, otherwise only general purpose metrics will be reported over mqtt. Typically you should set it to either string or micro. Additional groups may be added in the future.

Metric	Modbus address	MQTT topic suffix	Unit	Groups
Production today	0x3c	day_energy	kWh
Uptime	0x3e	uptime	minutes
Total Production (Active)	0x3F - 0x40	total_energy	kWh
Daily Production 1	0x41	dc/pv1/day_energy	kWh	micro
Daily Production 2	0x42	dc/pv2/day_energy	kWh	micro
Daily Production 3	0x43	dc/pv3/day_energy	kWh	micro
Daily Production 4	0x44	dc/pv4/day_energy	kWh	micro
Total Production 1	0x45 - 0x46	dc/pv1/total_energy	kWh	micro
Total Production 2	0x47 - 0x48	dc/pv2/total_energy	kWh	micro
Total Production 3	0x4a - 0x4b	dc/pv3/total_energy	kWh	micro
Total Production 4	0x4d - 0x4e	dc/pv4/total_energy	kWh	micro
AC Phase 1 voltage	0x49	ac/l1/voltage	V	string, micro
AC Phase 2 voltage	0x4a	ac/l2/voltage	V	string
AC Phase 3 voltage	0x4b	ac/l3/voltage	V	string
AC Phase 1 current	0x4c	ac/l1/current	A	string, micro
AC Phase 2 current	0x4d	ac/l2/current	A	string
AC Phase 3 current	0x4e	ac/l3/current	A	string
AC Frequency	0x4f	ac/freq	Hz
Operating power	0x50	operating_power	W	string, micro
DC total power	0x52	dc/total_power	W	string, micro
AC apparent power	0x54	ac/apparent_power	W	string, micro
AC active power	0x56 - 0x57	ac/active_power	W	string, micro
AC reactive power	0x58	ac/reactive_power	W	string, micro
Radiator temperature	0x5a	radiator_temp	C
IGBT temperature	0x5b	igbt_temp	C
DC PV1 voltage	0x6d	dc/pv1/voltage	V
DC PV1 current	0x6e	dc/pv1/current	A
DC PV2 voltage	0x6f	dc/pv2/voltage	V
DC PV2 current	0x70	dc/pv2/current	A
DC PV3 voltage	0x71	dc/pv3/voltage	V
DC PV3 current	0x72	dc/pv3/current	A
DC PV4 voltage	0x73	dc/pv4/voltage	V
DC PV4 current	0x74	dc/pv4/current	A

Installation

1. Copy config.env.example as config.env

2. Fill in values in config.env

3. Run the container

   docker run --rm --env-file config.env ghcr.io/kbialek/deye-inverter-mqtt
   

Configuration

All configuration options are controlled through environment variables.

• LOG_LEVEL - application log level, can be any of DEBUG, INFO, WARN, ERROR
• DEYE_DATA_READ_INTERVAL - interval between subsequent data reads, in seconds, defaults to 60
• DEYE_METRIC_GROUPS - a comma delimited set of:
  • string - set when connecting to a string inverter
  • micro - set when connecting to a micro inverter
• DEYE_LOGGER_SERIAL_NUMBER - inverter data logger serial number
• DEYE_LOGGER_IP_ADDRESS - inverter data logger IP address
• DEYE_LOGGER_PORT - inverter data logger communication port, typically 8899
• MQTT_HOST
• MQTT_PORT
• MQTT_USERNAME
• MQTT_PASSWORD
• MQTT_TOPIC_PREFIX - mqtt topic prefix used for all inverter metrics

Reading and writing raw register values

The tool allows reading and writing raw register values directly in the terminal.

USE AT YOUR OWN RISK! Be sure to know what you are doing. Writing invalid values may damage the inverter. By using this tool you accept this risk and you take full responsiblity for the consequences.

• To read register value execute:

  docker run --rm --env-file config.env ghcr.io/kbialek/deye-inverter-mqtt r <reg_address>
  

  where <reg_address> is register address (decimal)

• To write register value execute:

  docker run --rm --env-file config.env ghcr.io/kbialek/deye-inverter-mqtt w <reg_address> <reg_value>
  

  where <reg_address> is register address (decimal), and <reg_value> is a value to set (decimal)

Development

1. Install python dependencies

   pip install -r requirements.txt
   

2. Running the code
   1. Option 1 - Run the code locally without using Docker
      1. Fill in config.env file
      2. Execute make run
   2. Option 2 - Build a new docker image locally (for amd64 architecture)
      1. Execute make docker-build-local
      2. Fill in config.env file
      3. Execute make docker-run
3. To run the tests use make test