deepmean / shell-aliyundrive

One-click setup Aliyun Drive on your router that have installed Padavan or other firmware based on linux.

shell-aliyundrive 阿里云webdav一键自动安装脚本

One-click setup Aliyun-drive webdav service on your wireless router that have installed Padavan or other firmware based on linux kernel.

Optional setup: Mount webdav as filesytem and sharing with SAMBA (linux kernel module fuse is required and setup fusermount, webdavfs - recommended or davfs2

• 在路由器上一键安装阿里云盘webDav服务（路由器需要刷Padavan或OpenWRT等基于linux内核的固件）
• 可选安装：阿里云盘挂载和SAMBA共享 (需要linux内核集成fuse，并安装fusermount, webdavfs - 推荐 或 davfs2

快速安装阿里云WebDav服务 / fusemount (可选，加载WebDav服务作为本地磁盘)

以Padavan固件路由器安装为例：下载aliyundrive_install.sh 到路径/etc/storage/

执行命令：

cd /etc/storage && chmod +x aliyundrive_install.sh && ./aliyundrive_install.sh [refresh token]

替换参数[refresh token]：点我获取refresh token

• 注意 上面命令可以不指定[refresh_token]，但必须在终端控制台运行命令，安装过程中将会看到【 扫描二维码登录获取refresh_token 】: 打开手机阿里云APP (版本4.9.1或以下) 扫描 , 请按提示完成后续操作即可。
• WebDav服务安装完成后，请访问流媒体文件服务地址：http://admin:[email protected]:8080 (0.0.0.0表示安装路由器内部网络地址，或替换为路由器内部网络真实地址，如: http://admin:[email protected]:8080) 。此外，也可以从外部网络直接访问webdav服务, 例如, 安装webdav的路由器连到上级路由器所分配地址是192.168.1.123，那么与上级路由器在同一子网的任何设备可直接访问http://admin:[email protected]:8080
• 安装稳定版本：多次安装失败报检测版本错误，请替换命令中的aliyun_drive_install.sh成为aliyun_drive_install_stable.sh
• 可选插件安装 - webdavfs / fusermount 支持fuse mount插件， 需要下载mount_aliyun.sh放到与主安装程序aliyundrive_install.sh同一目录下，执行相同的快速安装命令(见上面) 加载后的阿里云盘作为文件系统，默认路径/mnt/aliyun

---

Quick setup webdav serivce & fuse mount (optional)

Please copy ./aliyundrive_install.sh to /etc/storage/ or anywhere you like then copy / run the following command as follows to finish the installation.

chmod +x /etc/storage/aliyundrive_install.sh &&
/etc/storage/aliyundrive_install.sh [refresh_token] [platform]

[refresh_token] is required that you extracted from web browser on aliyundrive.com

Click me to get refresh token

If you don't give [refresh_token], then you'll have to run the command in terminal console, then you will see the following instruction:【 扫描二维码登录获取refresh_token 】: 打开手机阿里云APP (版本4.9.1或以下) 扫描 , Please launch AliYun app on your phone, then scanning the QR code for login to finish the setup.

[platform] is optional by default is mipsel (联发科soc), the valid platform can be in [aarch64, arm, arm5te, armv7, mips, mipsel, x86_64] 如果你的路由器是 Intel soc, 选x86_64; 如果你的路由器是 ARM soc, 选arm | arm5te | armv7

Now, the main script aliyundrive_install.sh will launch aliyundrive-webdav with specific parameters, the webdav service works on http://admin:[email protected]:8080

For Padavan, you would like to run the following extra command to permanently save the script, you will be able to rerun the script once you encounter any throuble~

/sbin/mtd_storage.sh save

How to fetch refresh token

点我查看获取refresh token

Optional setup (only support MIPS little endian arch.)

Please copy ./mount_aliyun.sh' to the same directory with ./aliyundrive_install.sh` When running the following command, it will auto-install and mount the webdav service http://admin:[email protected]:8080 into local directory /mnt/aliyun

/etc/storage/aliyundrive_install.sh [refresh_token] [platform]

Now, you can access AliCloud storage more easily at local disk. Furthermore, you can share the directory /mnt/aliyun with other network devices in same sub-network, this can be finished by SAMBA , you simply copy smb.conf start_samba.sh to somewhere, then change start_samba.conf with executable permission and execute it to setup SAMBA share service.

chmod +x ./start_samba.sh && ./start_samba.sh

Uninstall [卸载]

/etc/storage/aliyundrive_install.sh uninstall

Performance [性能]

There are two special parameters that you would like to tweak in the script, please find the codes as follows:

--read-buffer-size 1048576 --upload-buffer-size 1048576

if your router owns plenty of memory more than 256MB , you should remove the two parameters or increase the buffer size in bytes. otherwise, please keep it at the fixed buffer size at 1MB, this will avoid crashing with error memory allocation failed.

Development story

k2p is a router branding by phicomm (this company has bankrapted for years for some reasons ), the router is able to flash custom firmware that will increases a great performance on wireless connection. I was going to deploy the AliyunDrive on it using 'WebDav' protocol , but the router has lower memory at 128M RAM, and 16M flash memory only! due to the low flash memory, I couldn't put the binary in the flash memory then launch it, But it's able to run the binary from the 128M RAM!! Finally, I've created the main script aliyundrive_install.sh that successfully setup / run aliyundrive-webdav from RAM .

Reference

aliyundrive-webdav https://github.com/messense/aliyundrive-webdav

webdavfs https://github.com/simonchen/webdavfs

libfuse https://github.com/simonchen/libfuse

davfs2 https://github.com/simonchen/davfs2