Firmware Analysis Toolkit

FAT is a toolkit built in order to help security researchers analyze and identify vulnerabilities in IoT and embedded device firmware. This is built in order to use for the "Offensive IoT Exploitation" training conducted by Attify.

Note:

As of now, it is simply a script to automate Firmadyne which is a tool used for firmware emulation. In case of any issues with the actual emulation, please post your issues in the firmadyne issues.
In case you are facing issues, you can try AttifyOS which has Firmware analysis toolkit and other tools pre-installed and ready to use.

Firmware Analysis Toolkit (FAT henceforth) is based on Firmadyne with some changes. Firmadyne uses a PostgreSQL database to store information about the emulated images. However just for the core functionality i.e. emulating firmware, PostgreSQL is not really needed. Hence FAT doesn't use it.

Setup instructions

FAT is developed in Python 3. However you need to have both Python 3 and Python 2 installed since parts of Firmadyne and its dependencies use Python 2. It's highly recommended to install FAT inside a Virtual Machine.

To install just clone the repository and run the script ./setup.sh.

git clone https://github.com/attify/firmware-analysis-toolkit
cd firmware-analysis-toolkit
./setup.sh

After installation is completed, edit the file fat.config and provide the sudo password as shown below. Firmadyne requires sudo privileges for some of its operations. The sudo password is provided to automate the process.

[DEFAULT]
sudo_password=attify123
firmadyne_path=/home/attify/firmadyne

Running FAT

$ ./fat.py <firmware file>

Provide the firmware filename as an argument to the script.
The script would display the IP addresses assigned to the created network interfaces. Note it down.
Finally, it will say that running the firmware. Hit ENTER and wait until the firmware boots up. Ping the IP which was shown in the previous step, or open in the browser.

Congrats! The firmware is finally emulated.

To remove all analyzed firmware images, run

$ ./reset.py

Example 1

$ ./fat.py DIR-601_REVB_FIRMWARE_2.01.BIN 

                               __           _   
                              / _|         | |  
                             | |_    __ _  | |_ 
                             |  _|  / _` | | __|
                             | |   | (_| | | |_ 
                             |_|    \__,_|  \__|                    
                    
                Welcome to the Firmware Analysis Toolkit - v0.3
    Offensive IoT Exploitation Training http://bit.do/offensiveiotexploitation
                  By Attify - https://attify.com  | @attifyme
    
[+] Firmware: DIR-601_REVB_FIRMWARE_2.01.BIN
[+] Extracting the firmware...
[+] Image ID: 1
[+] Identifying architecture...
[+] Architecture: mipseb
[+] Building QEMU disk image...
[+] Setting up the network connection, please standby...
[+] Network interfaces: [('br0', '192.168.0.1')]
[+] All set! Press ENTER to run the firmware...
[+] When running, press Ctrl + A X to terminate qemu

Asciicast

Example 2

$ ./fat.py DIR890A1_FW103b07.bin --qemu 2.5.0

                               __           _
                              / _|         | |
                             | |_    __ _  | |_
                             |  _|  / _` | | __|
                             | |   | (_| | | |_
                             |_|    \__,_|  \__|

                Welcome to the Firmware Analysis Toolkit - v0.3
    Offensive IoT Exploitation Training http://bit.do/offensiveiotexploitation
                  By Attify - https://attify.com  | @attifyme

[+] Firmware: DIR890A1_FW103b07.bin
[+] Extracting the firmware...
[+] Image ID: 2
[+] Identifying architecture...
[+] Architecture: armel
[+] Building QEMU disk image...
[+] Setting up the network connection, please standby...
[+] Network interfaces: [('br0', '192.168.0.1'), ('br1', '192.168.7.1')]
[+] Using qemu-system-arm from /home/attify/firmware-analysis-toolkit/qemu-builds/2.5.0
[+] All set! Press ENTER to run the firmware...
[+] When running, press Ctrl + A X to terminate qemu

Additional Notes

As of now, the ARM firmadyne kernel doesn't work with the latest version of Qemu (2.11.1) available on the Ubuntu 18.04 official repository. However, Qemu (2.5.0) on Ubuntu 16.04 does work. Alternatively you can also use the bundled Qemu (2.5.0) provided with firmadyne as shown in example 2.

If no network interfaces are detected, try increasing the timeout value from 60 in scripts/inferNetwork.sh as shown below

echo "Running firmware ${IID}: terminating after 60 secs..."
timeout --preserve-status --signal SIGINT 60 "${SCRIPT_DIR}/run.${ARCH}.sh" "${IID}"

Known Issues

~~FAT does not work on Ubuntu 20.04. The main reason behind this is some dependencies of Firmadyne (especially binwalk) require Python 2. Unless this is fixed upstream, stick to Ubuntu 18.04 or lower.~~ Ubuntu 20.04 is now supported. The current version of FAT patches the binwalk installation script to workaround the issue.

eatonchips / firmware-analysis-toolkit Goto Github PK