infineon / mtb-example-hal-gpio-interrupt

This example demonstrates how to configure a GPIO to generate an interrupt in PSoC 6 MCU.

HAL: GPIO interrupt

This code example demonstrates the use of a GPIO configured as an input pin to generate interrupts on an Infineon MCU. The GPIO signal interrupts the CPU and executes a user-defined interrupt service routine (ISR). The GPIO interrupt acts as a wakeup source to wake the CPU from deepsleep.

View this README on GitHub.

Provide feedback on this code example.

Requirements

• ModusToolbox™ v3.1 or later (tested with v3.1)
• Board support package (BSP) minimum required version for:
  • PSoC™ 6 MCU: v4.1.0
  • KIT_XMC72_EVK: v1.1.0
  • CYW920829M2EVK-02: v1.0.1
  • CYW989829M2EVB-01: v1.0.2
• Programming language: C
• Associated parts: All PSoC™ 6 MCU parts, XMC7000 MCU, AIROC™ CYW20829 Bluetooth® LE SoC and AIROC™ CYW89829 Bluetooth® LE SoC

Supported toolchains (make variable 'TOOLCHAIN')

• GNU Arm® Embedded Compiler v11.3.1 (GCC_ARM) – Default value of TOOLCHAIN
• Arm® Compiler v6.16 (ARM)
• IAR C/C++ Compiler v9.30.1 (IAR)

Supported kits (make variable 'TARGET')

• PSoC™ 62S2 Wi-Fi Bluetooth® Prototyping Kit (CY8CPROTO-062S2-43439) – Default value of TARGET
• PSoC™ 6 Wi-Fi Bluetooth® Prototyping Kit (CY8CPROTO-062-4343W)
• AIROC™ CYW20829 Bluetooth® LE evaluation Kit (CYW920829M2EVK-02)
• AIROC™ CYW89829 Bluetooth® LE evaluation kit – (CYW89829M2EVB-01)
• PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit (CY8CKIT-062-WIFI-BT)
• PSoC™ 6 Bluetooth® LE Pioneer Kit (CY8CKIT-062-BLE)
• PSoC™ 6 Bluetooth® LE Prototyping Kit (CY8CPROTO-063-BLE)
• PSoC™ 62S2 Wi-Fi Bluetooth® Pioneer Kit (CY8CKIT-062S2-43012)
• PSoC™ 62S1 Wi-Fi Bluetooth® Pioneer Kit (CYW9P62S1-43438EVB-01)
• PSoC™ 62S1 Wi-Fi Bluetooth® Pioneer Kit (CYW9P62S1-43012EVB-01)
• PSoC™ 62S3 Wi-Fi Bluetooth® Prototyping Kit (CY8CPROTO-062S3-4343W)
• EZ-BLE Arduino Evaluation Board (CYBLE-416045-EVAL)
• PSoC™ 64 "Secure Boot" Wi-Fi Bluetooth® Pioneer Kit (CY8CKIT-064B0S2-4343W)
• PSoC™ 62S4 Pioneer Kit (CY8CKIT-062S4)
• PSoC™ 62S2 Evaluation Kit (CY8CEVAL-062S2, CY8CEVAL-062S2-LAI-4373M2, CY8CEVAL-062S2-LAI-43439M2, CY8CEVAL-062S2-MUR-43439M2, CY8CEVAL-062S2-MUR-4373M2, CY8CEVAL-062S2-MUR-4373EM2)
• XMC™ 7200 evaluation kit (KIT_XMC72_EVK)
• PSoC™ 64 "Secure Boot" Prototyping Kit (CY8CPROTO-064B0S3)
• PSoC™ 64 "Secure Boot" Prototyping Kit (CY8CPROTO-064S1-SB)
• XMC7100 Evaluation Kit (KIT_XMC71_EVK_LITE_V1)

Hardware setup

This example uses the board's default configuration. See the kit user guide to ensure that the board is configured correctly.

Note: The PSoC™ 6 Bluetooth® LE Pioneer Kit (CY8CKIT-062-BLE) and the PSoC™ 6 Wi-Fi Bluetooth® Pioneer Kit (CY8CKIT-062-WIFI-BT) ship with KitProg2 installed. ModusToolbox™ requires KitProg3. Before using this code example, make sure that the board is upgraded to KitProg3. The tool and instructions are available in the Firmware Loader GitHub repository. If you do not upgrade, you will see an error like "unable to find CMSIS-DAP device" or "KitProg firmware is out of date".

The AIROC™ CYW20829 Bluetooth® kit (CYW920829M2EVK-02) ships with KitProg3 version 2.21 installed. The ModusToolbox™ software requires KitProg3 with latest version 2.40. Before using this code example, make sure that the board is upgraded to KitProg3. The tool and instructions are available in the Firmware Loader GitHub repository. If you do not upgrade, you will see an error like "Unable to find CMSIS-DAP device" or "KitProg firmware is out of date".

Software setup

See the ModusToolbox™ tools package installation guide for information about installing and configuring the tools package.

Install a terminal emulator if you don't have one. Instructions in this document use Tera Term.

This example requires no additional software or tools.

Using the code example

Create the project

The ModusToolbox™ tools package provides the Project Creator as both a GUI tool and a command line tool.

Use Project Creator GUI

1. Open the Project Creator GUI tool.

   There are several ways to do this, including launching it from the dashboard or from inside the Eclipse IDE. For more details, see the Project Creator user guide (locally available at {ModusToolbox™ install directory}/tools_{version}/project-creator/docs/project-creator.pdf).

2. On the Choose Board Support Package (BSP) page, select a kit supported by this code example. See Supported kits.

   Note: To use this code example for a kit not listed here, you may need to update the source files. If the kit does not have the required resources, the application may not work.

3. On the Select Application page:

   a. Select the Applications(s) Root Path and the Target IDE.

   Note: Depending on how you open the Project Creator tool, these fields may be pre-selected for you.

   b. Select this code example from the list by enabling its check box.

   Note: You can narrow the list of displayed examples by typing in the filter box.

   c. (Optional) Change the suggested New Application Name and New BSP Name.

   d. Click Create to complete the application creation process.

Use Project Creator CLI

The 'project-creator-cli' tool can be used to create applications from a CLI terminal or from within batch files or shell scripts. This tool is available in the {ModusToolbox™ install directory}/tools_{version}/project-creator/ directory.

Use a CLI terminal to invoke the 'project-creator-cli' tool. On Windows, use the command-line 'modus-shell' program provided in the ModusToolbox™ installation instead of a standard Windows command-line application. This shell provides access to all ModusToolbox™ tools. You can access it by typing "modus-shell" in the search box in the Windows menu. In Linux and macOS, you can use any terminal application.

The following example clones the "mtb-example-hal-gpio-interrupt" application with the desired name "GpioInterrupt" configured for the CY8CPROTO-062S2-43439 BSP into the specified working directory, C:/mtb_projects:

project-creator-cli --board-id CY8CPROTO-062S2-43439 --app-id mtb-example-hal-gpio-interrupt --user-app-name GPIOInt --target-dir "C:/mtb_projects"

The 'project-creator-cli' tool has the following arguments:

Argument	Description	Required/optional
--board-id	Defined in the field of the BSP manifest	Required
--app-id	Defined in the field of the CE manifest	Required
--target-dir	Specify the directory in which the application is to be created if you prefer not to use the default current working directory	Optional
--user-app-name	Specify the name of the application if you prefer to have a name other than the example's default name	Optional

Note: The project-creator-cli tool uses the git clone and make getlibs commands to fetch the repository and import the required libraries. For details, see the "Project creator tools" section of the ModusToolbox™ tools package user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mtb_user_guide.pdf).

Open the project

After the project has been created, you can open it in your preferred development environment.

Eclipse IDE

If you opened the Project Creator tool from the included Eclipse IDE, the project will open in Eclipse automatically.

For more details, see the Eclipse IDE for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_ide_user_guide.pdf).

Visual Studio (VS) Code

Launch VS Code manually, and then open the generated {project-name}.code-workspace file located in the project directory.

For more details, see the Visual Studio Code for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_vscode_user_guide.pdf).

Keil µVision

Double-click the generated {project-name}.cprj file to launch the Keil µVision IDE.

For more details, see the Keil µVision for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_uvision_user_guide.pdf).

IAR Embedded Workbench

Open IAR Embedded Workbench manually, and create a new project. Then select the generated {project-name}.ipcf file located in the project directory.

For more details, see the IAR Embedded Workbench for ModusToolbox™ user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mt_iar_user_guide.pdf).

Command line

If you prefer to use the CLI, open the appropriate terminal, and navigate to the project directory. On Windows, use the command-line 'modus-shell' program; on Linux and macOS, you can use any terminal application. From there, you can run various make commands.

For more details, see the ModusToolbox™ tools package user guide (locally available at {ModusToolbox™ install directory}/docs_{version}/mtb_user_guide.pdf).

Operation

If using a PSoC™ 64 "Secure" MCU kit (like CY8CKIT-064B0S2-4343W), the PSoC™ 64 device must be provisioned with keys and policies before being programmed. Follow the instructions in the "Secure Boot" SDK user guide to provision the device. If the kit is already provisioned, copy-paste the keys and policy folder to the application folder.

1. Connect the board to your PC using the provided USB cable through the KitProg3 USB connector.

2. Open a terminal program and select the KitProg3 COM port. Set the serial port parameters to 8N1 and 115200 baud.

3. Program the board using one of the following:

   Using Eclipse IDE

   1. Select the application project in the Project Explorer.

   2. In the Quick Panel, scroll down, and click <Application Name> Program (KitProg3_MiniProg4).

   In other IDEs

   Follow the instructions in your preferred IDE.

   Using CLI

   From the terminal, execute the make program command to build and program the application using the default toolchain to the default target. The default toolchain is specified in the application's Makefile but you can override this value manually:

   make program TOOLCHAIN=<toolchain>
   

   Example:

   make program TOOLCHAIN=GCC_ARM
   

4. After successful programming, the terminal should display the message as follows:

   Figure 1. Sample output

   

   Also, observe that the user LED blinks four times and then turns OFF, indicating that the CPU has entered deepsleep.

5. Press the user button to trigger an interrupt. This should wake up the device, causing the LED to resume blinking at a faster rate (default = 2 Hz). The faster blink rate indicates that the ISR has executed to change the delay variable used to determine the LED blink rate. The LED blinks four times and the device enters deepsleep again.

6. Press the button again to repeat the wakeup cycle, and the LED resumes blinking at the slower rate (default = 1 Hz). With every interrupt and execution of ISR, the interval of blinking is alternated between the slower and faster rates.

Debugging

You can debug the example to step through the code.

In Eclipse IDE

Use the <Application Name> Debug (KitProg3_MiniProg4) configuration in the Quick Panel. For details, see the "Program and debug" section in the Eclipse IDE for ModusToolbox™ user guide.

Note: (Only while debugging) On the CM4 CPU, some code in main() may execute before the debugger halts at the beginning of main(). This means that some code executes twice – once before the debugger stops execution, and again after the debugger resets the program counter to the beginning of main(). See KBA231071 to learn about this and for the workaround.

In other IDEs

Follow the instructions in your preferred IDE.

Design and implementation

Resources and settings

This code example uses a GPIO interrupt to wake the Arm® Cortex®-M4 or Cortex®-M7 CPU from deepsleep. An LED is connected to an output pin; it is used for indicating the current state of the CPU. A blinking LED indicates that the CPU is active. After four successive blinks, the CPU is instructed to enter deepsleep. The GPIO state is retained during deepsleep, so the LED stops blinking and stays OFF to indicate that the CPU is in deepsleep.

An input pin, externally connected to a switch, is configured to generate an interrupt when the switch is pressed. The interrupt triggers the following two actions:

1. Generates a signal that wakes the CPU from deepsleep.

2. Executes an ISR.

When the ISR is executed, a flag is updated, which is used to change the rate at which the LED blinks. With every press of the switch, the LED alternates the blinking interval.

Table 1. Application resources

Resource	Alias/object	Purpose
UART (HAL)	cy_retarget_io_uart_obj	UART HAL object used by Retarget-IO for the Debug UART port
GPIO (HAL)	CYBSP_USER_LED	User LED to show visual output

Related resources

Resources	Links
Application notes	AN228571 – Getting started with PSoC™ 6 MCU on ModusToolbox™ AN215656 – PSoC™ 6 MCU: Dual-CPU system design AN234334 – Getting started with XMC7000 MCU on ModusToolbox™ software
Code examples	Using ModusToolbox™ on GitHub
Device documentation	PSoC™ 6 MCU datasheets PSoC™ 6 technical reference manuals XMC7000 MCU datasheets XMC7000 MCU technical reference manuals AIROC™ CYW20829 Bluetooth® LE SoC
Development kits	Select your kits from the Evaluation board finder.
Libraries on GitHub	mtb-pdl-cat1 – PSoC™ 6 Peripheral Driver Library (PDL) mtb-hal-cat1 – Hardware Abstraction Layer (HAL) library retarget-io – Utility library to retarget STDIO messages to a UART port
Middleware on GitHub	capsense – CAPSENSE™ library and documents psoc6-middleware – Links to all PSoC™ 6 MCU middleware
Tools	ModusToolbox™ – ModusToolbox™ software is a collection of easy-to-use libraries and tools enabling rapid development with Infineon MCUs for applications ranging from wireless and cloud-connected systems, edge AI/ML, embedded sense and control, to wired USB connectivity using PSoC™ Industrial/IoT MCUs, AIROC™ Wi-Fi and Bluetooth® connectivity devices, XMC™ Industrial MCUs, and EZ-USB™/EZ-PD™ wired connectivity controllers. ModusToolbox™ incorporates a comprehensive set of BSPs, HAL, libraries, configuration tools, and provides support for industry-standard IDEs to fast-track your embedded application development.

Other resources

Infineon provides a wealth of data at www.infineon.com to help you select the right device, and quickly and effectively integrate it into your design.

For PSoC™ 6 MCU devices, see How to design with PSoC™ 6 MCU - KBA223067 in the Infineon developer community.

For XMC™ MCU devices, see 32-bit XMC™ Industrial microcontroller based on Arm® Cortex®-M.

Document history

Document title: CE219521 – HAL: GPIO interrupt

Version	Description of change
1.0.0	New code example
1.1.0	Updated to support ModusToolbox™ software v2.1, added new kits
2.0.0	Major update to support ModusToolbox™ software v2.2, added support for new kits. This version is not backward compatible with ModusToolbox™ software v2.1.
2.1.0	Added support for CYSBSYSKIT-DEV-01 Rapid IoT Connect developer kit.
2.2.0	Updated to support ModusToolbox™ software v2.3. Added support for new kits.
3.0.0	Major update to support ModusToolbox™ software v3.0, added support for KIT_XMC72_EVK.
3.1.0	Added support for CY8CEVAL-062S2-MUR-43439M2, CY8CPROTO-064B0S3, CY8CPROTO-064S1-SB and CYW920829M2EVB-01.
3.2.0	Removed CYW920829M2EVB-01 from supported kits Added support for CYBLE-416045-EVAL and CYW920829M2EVK-02
3.2.1	Readme Update
3.3.0	Updated to support ModusToolbox™ v3.1. Added support for KIT_XMC71_EVK_LITE_V1, CY8CPROTO-062S2-43439, CY8CEVAL-062S2-LAI-43439M2, CY8CEVAL-062S2-MUR-4373M2, CY8CEVAL-062S2-MUR-4373EM2
3.4.0	Added support for CYW989829M2EVB-01.

All referenced product or service names and trademarks are the property of their respective owners.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Infineon is under license.

---

© Cypress Semiconductor Corporation, 2020-2023. This document is the property of Cypress Semiconductor Corporation, an Infineon Technologies company, and its affiliates ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no liability arising out of any security breach, such as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING CYPRESS PRODUCTS, WILL BE FREE FROM CORRUPTION, ATTACK, VIRUSES, INTERFERENCE, HACKING, DATA LOSS OR THEFT, OR OTHER SECURITY INTRUSION (collectively, "Security Breach"). Cypress disclaims any liability relating to any Security Breach, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. "High-Risk Device" means any device or system whose failure could cause personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and other medical devices. "Critical Component" means any component of a High-Risk Device whose failure to perform can be reasonably expected to cause, directly or indirectly, the failure of the High-Risk Device, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of a Cypress product as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, including its affiliates, and its directors, officers, employees, agents, distributors, and assigns harmless from and against all claims, costs, damages, and expenses, arising out of any claim, including claims for product liability, personal injury or death, or property damage arising from any use of a Cypress product as a Critical Component in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except to the limited extent that (i) Cypress's published data sheet for the product explicitly states Cypress has qualified the product for use in a specific High-Risk Device, or (ii) Cypress has given you advance written authorization to use the product as a Critical Component in the specific High-Risk Device and you have signed a separate indemnification agreement.
Cypress, the Cypress logo, and combinations thereof, ModusToolbox, PSoC, CAPSENSE, EZ-USB, F-RAM, and TRAVEO are trademarks or registered trademarks of Cypress or a subsidiary of Cypress in the United States or in other countries. For a more complete list of Cypress trademarks, visit www.infineon.com. Other names and brands may be claimed as property of their respective owners.