kvazis / training Goto Github PK

Несколько перегруженный вариант кондиций ... системе несколько раз приходится пересчитывать чтобы проверить на разницу в 0.5 и в -0.5 ... хотя можно не нагружать систему расчетами лишними

  condition:
    - condition: template
      value_template: >-
        {% set v = (((states.sensor.kitchen_climat_temperature.state | float) - (state_attr('climate.kitchen_thermostat', 'local_temperature') | float)) | round(1)) %}
        {{ v >= 0.5 or v <= -0.5 }}

вместо

condition:
      condition: or
      conditions:
        - condition: template
          value_template: '{{ states.sensor.temperature_sensor_spalnya_temperature.state | float | round(1) - state_attr("climate.thermostat_spalnya", "local_temperature") | float | round(1) > 0.5 }}'
        - condition: template
          value_template: '{{ states.sensor.temperature_sensor_spalnya_temperature.state | float | round(1) - state_attr("climate.thermostat_spalnya", "local_temperature") | float | round(1) < -0.5 }}'

PS
Опять же излишнее кол-во раз округление ...
Так же я бы добавил еще одно ограничение ... летом лишний раз гонять термостат нет смысла ... особенно если говорить о городской квартире. Летом отопления в трубах нет ...

    - condition: template
      value_template: >
        {% set n = now() %}
        {{ n.month >= 9 or n.month <= 4 }}

Заодно на лето я бы так же уводил термостат в режим OFF чтобы опять же не гоняло лишний раз ее туда сюда

PPS
Опять же не скажу за SEA801 ... но например SEA802 калибровка идет в пределах 1 градуса без возможности установить 0.5 или 0.6 и тп ... т.е не понятно зачем проверять условие разницы в 0.5 .... условие 0.5 сработает передвинем допустим на +1 градус что создаст через 10 минут обратный эфект и оно будет уже двигать температуру обратно ... так и будет туда сюда жужжать термостатом надо проверять в минимуме на разницу >= +1 или -1 градус

Добрый день, Во первых спасибо за ваши уроки!)))

Уже третий день бадаюсь с установкой убунту на ссд диск. Raspberry 4b 4GB. переходник, ссд 256gb
Во первых почему то получилось только через beta бутлоадер (usb)
После установки через raspberry pi image убунту на диск, система в первый раз стартует очень долго, час наверное (соотвественно обрывал и пытался заного сделать, думал что не получилось)
Итого систему запустил, далее все по инструкции но после перезагрузки системы (35 строчка) ssh отвалился и не запускается, на самом распебери зел. диод коротко трижды моргает) при этом он также моргал и при первом запуске поэтому и обрывал, сам распбери пингуется. Провода hdmi нет , не могу посмотреть что ему не нравится(((

--------
sudo apt upgrade
sudo apt install net-tools network-manager
sudo systemctl start NetworkManager.service
sudo systemctl enable NetworkManager.service

sudo reboot

Подскажите плз что делаю не так?

I have been using this blueprint for a while successfully (knowing that I have to touch and hold the notification for the option/confirmation to be displayed.

Just tried it today and when I touch and hold, nothing happens (screen just gets blurry behind the message.

I am running
Home Assistant 2023.10.5
Supervisor 2023.10.0
Operating System 11.0

Also running IOS 17.0.3. (I don’t think I have tried to use this since updating to IOS 17, but also updated HA core just today.

I also found something else out. looking at the automation trace, it is showing that it continues to run and when calling the blueprint is waiting for a response - which I can’t give because the response screen isn’t coming up.

ALSO

Looking at the yaml code under blueprints, I see a concerning message on line 14:

integration: mobile_app.
There is a message next to this line in red that says:

String does not match the pattern of “DEPRECATED^”

and if you click on the red message, you can expand to get a description of the error:

String does not match the pattern of “DEPRECATED^”.yaml-schema: http://schemas.home-assistant.io/blueprint-script

I am assuming that something in one of the latest core updates has depreciated this call and it is no longer working.

Normally I use a notification group to send my notifications to multiple devices. I can't do that in this Blueprint because it need's a device id. Also adding multiple devices doesn't seem possible.

При выполнении sudo apt update зависало при обращении к archive.raspberrypi.org. Ping archive.raspberrypi.org тоже зависал. При этом ping google.com работал нормально. Сервер archive.raspberrypi.org пинговался без проблем с другого устройства этой локальной сети. Помогла смена DNS адреса на малинке. sudo nano /etc/resolv.conf и заменить адрес локального DNS сервера на 8.8.8.8. Это работает до перезагрузки. После установки network-manager первым DNS сервером вписать 8.8.8.8.
Видимо, вина роутера. Написал в Keenetic.

in latest homeassistant version python3.8 updated to python 3.9 so we need fix path to init.py

Supervisor will not run on docker 25.0.0

Can be fixed with Docker downgrade:

sudo apt install \
docker-ce=5:24.0.7-1~debian.12~bookworm \
docker-ce-cli=5:24.0.7-1~debian.12~bookworm \
docker-buildx-plugin=0.11.2-1~debian.12~bookworm \
docker-compose-plugin=2.21.0-1~debian.12~bookworm \
docker-ce-rootless-extras=5:24.0.7-1~debian.12~bookworm

sudo apt-mark hold \
docker-ce \
docker-ce-cli \
docker-buildx-plugin \
docker-compose-plugin \
docker-ce-rootless-extras

sudo reboot

Большое спасибо, лучшее по HA в зоне RU.

Hello,

i have this Problem after install today with your Manual.

Raspberry Output Version:

Jun 3 2020 13:53:47
version b5de8c32f4f45a12a1fdfe107254df82965f9d56 (release)
timestamp 1591188827

Linux 5.4.45-v7l+ #1321 SMP Wed Jun 10 17:39:20 BST 2020 armv7l GNU/Linux

Jun 10 2020 17:47:19
Copyright (c) 2012 Broadcom
version e46bba1638cca2708b31b9daf4636770ef981735 (clean) (release) (start

when i Shutdown Home Assistant it Shutdown my raspberry 4 too.
Is this right?

Why not only (Docker) Home Assistant - and Raspbian + Docker Remains active
And I have more Container than you after Fresh install.
homeassistant/raspberrypi4-homeassistant
homeassistant/armv7
supervisor
audio
dns
...

Log output Home Assistant

red Message:
20-06-15 16:31:51 ERROR (MainThread) [supervisor.docker] Docker logging driver json-file is not supported!
yellow Message:
20-06-15 16:31:51 WARNING (MainThread) [supervisor.dbus.rauc] Host has no rauc support. OTA updates have been disabled.
yellow Message:
20-06-15 16:31:56 WARNING (MainThread) [supervisor.hassos] No Home Assistant Operating System found!

Log complete:

20-06-15 16:31:50 INFO (MainThread) [supervisor.bootstrap] Use the old homeassistant repository for machine extraction
20-06-15 16:31:50 INFO (MainThread) [main] Initialize Supervisor setup
20-06-15 16:31:51 INFO (MainThread) [supervisor.bootstrap] Setup coresys for machine: raspberrypi4
20-06-15 16:31:51 INFO (SyncWorker_0) [supervisor.docker.supervisor] Attach to Supervisor homeassistant/armv7-hassio-supervisor with version 227
20-06-15 16:31:51 ERROR (MainThread) [supervisor.docker] Docker logging driver json-file is not supported!
20-06-15 16:31:51 INFO (MainThread) [main] Setup Supervisor
20-06-15 16:31:51 INFO (MainThread) [supervisor.utils.gdbus] Connect to dbus: org.freedesktop.systemd1 - /org/freedesktop/systemd1
20-06-15 16:31:51 INFO (MainThread) [supervisor.utils.gdbus] Connect to dbus: org.freedesktop.hostname1 - /org/freedesktop/hostname1
20-06-15 16:31:51 WARNING (MainThread) [supervisor.dbus.rauc] Host has no rauc support. OTA updates have been disabled.
20-06-15 16:31:51 INFO (MainThread) [supervisor.utils.gdbus] Connect to dbus: org.freedesktop.NetworkManager - /org/freedesktop/NetworkManager/DnsManager
20-06-15 16:31:51 INFO (MainThread) [supervisor.host.info] Update local host information
20-06-15 16:31:51 INFO (MainThread) [supervisor.utils.gdbus] Call org.freedesktop.DBus.Properties.GetAll on /org/freedesktop/hostname1
20-06-15 16:31:51 INFO (MainThread) [supervisor.host.services] Update service information
20-06-15 16:31:51 INFO (MainThread) [supervisor.utils.gdbus] Call org.freedesktop.systemd1.Manager.ListUnits on /org/freedesktop/systemd1
20-06-15 16:31:51 INFO (MainThread) [supervisor.host.network] Update local network DNS information
20-06-15 16:31:51 INFO (MainThread) [supervisor.utils.gdbus] Call org.freedesktop.DBus.Properties.GetAll on /org/freedesktop/NetworkManager/DnsManager
20-06-15 16:31:51 INFO (MainThread) [supervisor.host.sound] Update PulseAudio information
20-06-15 16:31:51 INFO (MainThread) [supervisor.host.apparmor] Load AppArmor Profiles: {'hassio-supervisor'}
20-06-15 16:31:51 INFO (MainThread) [supervisor.host.services] Reload local service hassio-apparmor.service
20-06-15 16:31:51 INFO (MainThread) [supervisor.utils.gdbus] Call org.freedesktop.systemd1.Manager.ReloadOrRestartUnit on /org/freedesktop/systemd1
20-06-15 16:31:51 INFO (SyncWorker_2) [supervisor.docker.interface] Attach to homeassistant/armv7-hassio-dns with version 9
20-06-15 16:31:51 INFO (MainThread) [supervisor.plugins.dns] Start CoreDNS plugin
20-06-15 16:31:51 INFO (MainThread) [supervisor.misc.forwarder] Start DNS port forwarding to 172.30.32.3
20-06-15 16:31:52 INFO (SyncWorker_3) [supervisor.docker.dns] Start DNS homeassistant/armv7-hassio-dns with version 9 - 172.30.32.3
20-06-15 16:31:52 INFO (MainThread) [supervisor.plugins.dns] Updated /etc/resolv.conf
20-06-15 16:31:52 INFO (SyncWorker_1) [supervisor.docker.interface] Attach to homeassistant/armv7-hassio-audio with version 14
20-06-15 16:31:52 INFO (MainThread) [supervisor.plugins.audio] Start Audio plugin
20-06-15 16:31:54 INFO (SyncWorker_8) [supervisor.docker.audio] Start Audio homeassistant/armv7-hassio-audio with version 14 - 172.30.32.4
20-06-15 16:31:54 INFO (SyncWorker_9) [supervisor.docker.interface] Attach to homeassistant/armv7-hassio-cli with version 25
20-06-15 16:31:54 INFO (MainThread) [supervisor.plugins.cli] Start cli plugin
20-06-15 16:31:55 INFO (SyncWorker_11) [supervisor.docker.cli] Start CLI homeassistant/armv7-hassio-cli with version 25 - 172.30.32.5
20-06-15 16:31:55 INFO (SyncWorker_12) [supervisor.docker.interface] Attach to homeassistant/armv7-hassio-multicast with version 2
20-06-15 16:31:55 INFO (MainThread) [supervisor.plugins.multicast] Start Multicast plugin
20-06-15 16:31:56 INFO (SyncWorker_14) [supervisor.docker.multicast] Start Multicast homeassistant/armv7-hassio-multicast with version 2 - Host
20-06-15 16:31:56 INFO (MainThread) [supervisor.updater] Fetch update data from https://version.home-assistant.io/stable.json
20-06-15 16:31:56 INFO (SyncWorker_5) [supervisor.docker.interface] Attach to homeassistant/raspberrypi4-homeassistant with version 0.111.2
20-06-15 16:31:56 WARNING (MainThread) [supervisor.hassos] No Home Assistant Operating System found!
20-06-15 16:31:56 INFO (MainThread) [supervisor.store.git] Load add-on /data/addons/core repository
20-06-15 16:31:56 INFO (MainThread) [supervisor.store.git] Load add-on /data/addons/git/a0d7b954 repository
20-06-15 16:31:56 INFO (MainThread) [supervisor.store] Load add-ons from store: 65 all - 65 new - 0 remove
20-06-15 16:31:56 INFO (MainThread) [supervisor.addons] Found 0 installed add-ons
20-06-15 16:31:56 INFO (MainThread) [supervisor.snapshots] Found 0 snapshot files
20-06-15 16:31:56 INFO (MainThread) [supervisor.discovery] Load 0 messages
20-06-15 16:31:56 INFO (MainThread) [supervisor.ingress] Load 0 ingress session
20-06-15 16:31:56 INFO (MainThread) [supervisor.misc.secrets] Load Home Assistant secrets: 1
20-06-15 16:31:56 INFO (MainThread) [main] Run Supervisor
20-06-15 16:31:56 INFO (MainThread) [supervisor.api] Start API on 172.30.32.2
20-06-15 16:31:56 INFO (MainThread) [supervisor.addons] Phase 'AddonStartup.INITIALIZE' start 0 add-ons
20-06-15 16:31:56 INFO (MainThread) [supervisor.addons] Phase 'AddonStartup.SYSTEM' start 0 add-ons
20-06-15 16:31:56 INFO (MainThread) [supervisor.addons] Phase 'AddonStartup.SERVICES' start 0 add-ons
20-06-15 16:31:56 INFO (SyncWorker_14) [supervisor.docker.interface] Start homeassistant/raspberrypi4-homeassistant
20-06-15 16:32:11 INFO (MainThread) [supervisor.homeassistant] Updated Home Assistant API token