Hide.me CLI is a VPN client for use with eVenture Ltd. Hide.me VPN service based on the WireGuard protocol. Client's features include:
- Completely standalone solution which does not depend on any external binaries or tools
- Key exchange via RESTful requests secured with TLS 1.3
- TLS certificate pinning of server's certificates to defeat man-in-the-middle sort of attacks
- Dead peer detection
- Leak protection a.k.a. kill-switch based on routing subsystem and packet marking
- Mobility/Roaming support
- DNS management
- IPv6 support
- systemd notification support
- Split tunneling
TODO:
- Server lists and server chooser
- Automatic server selection
- Client certificate authentication/authorization
You may clone this repository and run:
go build -o hide.me
Alternatively, download the latest build from the releases section.
Source tree and binary releases contain simple installation and uninstallation scripts. Hide.me CLI gets installed
in /opt/hide.me directory. Apart from copying hide.me files to /opt/hide.me no modifications to the system are done.
When systemd based distribution is detected the installer links a template unit file which can be used to instantiate
connections.
WireGuard is one of the most secure and simplest VPN tunneling solutions in the industry. It is easy to set up and use as long as no WireGuard public key exchange over an insecure medium (such as Internet) is required. Any sort of WireGuard public key exchange is out of the scope of the WireGuard specification.
The complicated task of public key exchange and secret key negotiation over an insecure medium is, usually, being handled by:
- IKE protocol - a hard to understand, and a rather complicated part of IPSec
- TLS protocol - a foundation for HTTPS and virtually any other secure protocol
hide.me implementation of WireGuard leverages HTTPS (TLS) for the exchange of:
- WireGuard Public keys
- WireGuard Shared keys
- IP addressing information (IP addresses, DNS server addresses,gateways...)
Authentication for all operations requires the use of an Access-Token. An Access-Token is a just a binary blob which is cryptographically tied to a hide.me account.
Connection to a hide.me VPN server gets established in these steps:
- hide.me CLI contacts a REST endpoint, over a secured channel, requesting a public key exchange and a server-side connection setup
- Server authenticates the request, sets up the connection and serves the IP addressing information (including the WireGuard endpoint address). Server issues a randomized Session-Token which may be used to disconnect this particular session
- hide.me CLI sets up a WireGuard peer according to the server's instruction and starts the DPD check loop
In contrast with many other solutions, hide.me CLI does not use any sort of Linux firewalling technology (IPTables, NFTables or eBPF). Instead of relying on Linux'es IP filtering frameworks, hide.me CLI selectively routes traffic by setting up a special routing table and a set of routing policy database rules. Blackhole routes in the aforementioned routing table drop all traffic unless it meets one of the following conditions:
- Traffic is local ( loopback interfaces, local broadcasts and IPv6 link-local multicast )
- DHCPv4 traffic
- Traffic is explicitly allowed by the means of the Split-tunneling option
- Traffic is marked
- Traffic is about to be tunneled
This mode of operation makes it possible for the users to establish their own firewalling policies with which hide.me CLI won't interfere.
Usage instructions may be printed by running hide.me CLI without any parameters.
Usage:
./hide.me [options...] <command> [host]
...
hide.me CLI user interface is quite simple. There are just three commands available:
command:
token - request an Access-Token (required for connect)
connect - connect to a vpn server
conf - generate a configuration file to be used with the -c option
In order to connect to a VPN server an Access-Token must be requested from a VPN server. An Access-Token request is issued by the token command. An Access-Token issued by any server may be used, for authentication purposes, with any other hide.me VPN server. When a server issues an Access-Token that token must be stored in a file. Default filename for an Access-Token is "accessToken.txt".
Once an Access-Token is in place it may be used for connect requests. Stale access tokens get updated automatically.
hide.me CLI does not necessarily have to be invoked with a bunch of command line parameters. Instead, a YAML formatted configuration file may be used to specify all the options. To generate such a configuration file the conf command may be used.
Note that there are a few options which are configurable only through the configuration file. Such options are:
- Password - DANGEROUS, do not use this option unless you're aware of the security implications
- ConnectTimeout
- AccessTokenUpdateDelay
host:
fqdn, short name or an IP address of a hide.me server
Required when the configuration file does not contain it
The hostname of a hide.me REST endpoint may be specified as a fully qualified domain name (nl.hide.me), short name (nl) or an IP address. There's no guarantee that the REST endpoint will match a WireGuard endpoint.
-4 Use IPv4 tunneling only
Limit all IP protocol operations to IPv4. Even though the server will provide IPv4 and IPv6 addressing only IPv4 addresses, IPv4 rules and IPv4 routes get installed. Leak protection/kill-switch works for IPv4 traffic only. IPv6 traffic flow remains unsecured.
WARNING: This option degrades security and should be used only when it's safe to do so, e.g. when the client machine has it's IPv6 stack disabled. Please, do not use it otherwise because IPv6 leaks may happen.
-6 Use IPv6 tunneling only
Limit all IP protocol operations to IPv6. Even though the server will provide IPv4 and IPv6 addressing only IPv6 addresses, IPv6 rules and IPv6 routes get installed. Leak protection/kill-switch works for IPv6 traffic only. IPv4 traffic flow remains unsecured.
WARNING: This option degrades security and should not be used unless the client wishes to tunnel the IPv6 traffic only.
-b filename
resolv.conf backup filename (default "/etc/resolv.conf.backup.hide.me")
When applying the DNS servers to the system hide.me CLI will back up /etc/resolv.conf file and create a new file in its place. Once the VPN session is over, DNS is restored by restoring the backup.
-c filename
Configuration filename
Use a configuration file named "filename".
-ca string
CA certificate bundle (default "CA.pem")
During TLS negotiation the VPN server's certificate needs to be verified. This option makes it possible to specify an alternate CA certificate bundle file.
-d DNS servers
comma separated list of DNS servers used for client requests (default "209.250.251.37:53,217.182.206.81:53")
By default, Hide.me CLI uses hide.me operated DNS servers to resolve VPN server names when issuing token or connect requests. The set of DNS servers used for these purposes may be customized with this option.
-dpd duration
DPD timeout (default 1m0s)
In order to detect if a connection has stalled, usually due to networking issues, hide.me CLI periodically checks the connection state. The checking period can be changed with this option, but can't be higher than a minute.
-i interface
network interface name (default "vpn")
Use this option to specify the name of the networking interface to create or use.
-l port
listen port
WireGuard kernel module may listen on a user-defined port for encrypted traffic.
-m mark
firewall mark for wireguard and hide.me client originated traffic (default 55555)
Hide.me CLI takes advantage of the WireGuard module's ability to mark WireGuard traffic. Packet marks make it possible for Linux to selectively route traffic according to RPDB policies.
Setting this option to any other value than 0 is supported, however setting it to 0 is not as such a setting turns off the required functionality.
-p port
remote port (default 432)
Remote REST endpoint port may be changed with this option.
-r table
routing table to use (default 55555)
Set the routing table to use for general traffic and leak protection mechanism.
-s networks
comma separated list of networks (CIDRs) for which to bypass the VPN
List of split-tunneled networks, i.e. the networks for which the traffic should not be tunneled over the VPN.
-t string
access token filename (default "accessToken.txt")
Name of the file which contains an Access-Token.
-u username
hide.me username
Set the hide.me username.
Hide.me CLI can be used standalone or as a systemd service. Using hide.me CLI as a systemd service allows you
to take advantage of systemd's dependancy resolution, monitoring and various hardening features.
The installer script links a template unit file [email protected] for you or you may manually link the template
unit file by running:
systemctl link hide.me@service
To manage connections the following commands may be used:
| Operation | Command |
|---|---|
| Create a connection | systemctl enable hide.me@SERVER |
| Start a connection | systemctl start hide.me@SERVER |
| Stop a connection | systemctl stop hide.me@SERVER |
| Remove a connection | systemctl disable hide.me@SERVER |
SERVER is a server name, group name or an IP address.
Service startup is considered successful when a connection to hide.me server gets completely established.
If you want to contribute to this project, please read the contribution guide.
React
Typescript
Django
Laravel
Facebook
Microsoft
Google
Alibaba
D3
Tencent