- Intel Edison × 1
- Intel Edison for Arduino × 1
- Base Shield V2 × 1
- Grove - Temperature&Humidity Sensor (High-Accuracy & Mini) × 1
- Grove - Moisture Sensor × 1
- Grove - Light Sensor × 1
- Grove - UV Sensor × 1
- Grove - PIR Motion Sensor × 1
- Grove – Encoder × 1
- Grove – Button × 1
- Grove - LCD RGB Backlight × 1
- Grove – Relay × 1
- Grove – Servo × 1
- Grove – Buzzer × 1
- 9V to Barrel Jack Adapter × 1
- 26AWG Grove Cable × 10
- USB Cable × 1
- Using 26AWG Grove Cable making the following connections:
| Grove Modules | Connected to |
|---|---|
| Temperature&Humidity Sensor | I2C |
| Moisture Sensor | A1 |
| Light Sensor | A2 |
| UV Sensor | A3 |
| PIR Motion Sensor | D7 |
| Encoder | D2 |
| Button | UART(D1) |
| LCD RGB Backlight | I2C |
| Relay | D5 |
| Servo | D6 |
| Buzzer | D4 |
- Set up the Development Environment, you can see the Edison Getting Started Guide.
- Download the library and demo from github
- Open Arduino IDE. Click Tools > Board and select Intel® Edison
- Click Tools > Serial Port and select the Com # that the Intel Edison is connected to
- Click Sketch > Import Library… > Add Library and import the library downloaded at step 3
- Click File > Examples > Grove_Indoor_Environment_Demo and select the demo
- Click the upload icon
- Open Tools > Serial Monitor, it will print the sensors’ information:
- Rotate the Encoder to check the sensor value on the LCD.
- In the Send TextBox, you can enter the following command to operate the sensors and actuators: Note:set [sensor][condition:>, < or =][ threshold],[actuator]=[action]
| Example | Description |
|---|---|
| set temp>40, relay=1 | if temperature is higher than 40°C, the relay opens. |
| set temp>40, sleep=1 | if temperature is >40°C, nothing to do. |
| set humi>60, buzzer=1 | if humidity is >60%, the buzzer beeps. |
| set light>600, servo=90 | if light intensity is >600, the servo truns 90°. |
| set uv>80, relay=0 | if UV intensity is >80, the relay closes. |
| set pir=1, buzzer=1 | If people detected, the buzzer beeps. |
| set ms>40, relay=1 | if moisture is >40, the relay opens. |
| set ssid=name, psw=password | set the wifi SSID and Password. |
You can open a web browser, and go to the IP address displayed on the Serial Monitor or LCD. The default port is 88.
Such as: 192.168.1.101:88
Note: 1. The command should be ended with /n, so “NewLine” (in the Serial Monitor) should be selected.
2. A actuator can only be controlled by a sensor. If A sensor wants to control a actuator (has be controlled by B sensor), B sensor should be set sleep.
This example uses a Grove - Moisture Sensor to detect the pot soil moisture and Grove – Relay to control a water-pump. When the moisture is lower than the threshold, the relay will open and the pump works until the moisture is higher than the threshold.
- Connect the device as above, and connect the water-pump:
- While connected, open the Serial Monitor,and send the command,as follows:
- Insert the Grove - Moisture Sensor into your pot, check the moisture value on the LCD.
- WiFi connection. open the Serial Monitor, and send the command as follows. Check the local IP on the LCD or Serial Monitor. On a device connected on the same network, open a web browser, and go to the IP address above, you can see the sensor value.
React
Typescript
Django
Laravel
Facebook
Microsoft
Google
Alibaba
D3
Tencent