tempbottle / dpdk-replay

This tool can replay a pcap capture at wire speed on several 10Gbps links.

DPDK-Replay

1. Description of the software

This tool can replay a pcap capture at wire speed on several 10Gbps links by means of DPDK APIs. It retreives the traffic from a file in pcap format and send it on the network interface(s). It can achieve high speed when the disks are fast.

• For information about DPDK please read: http://dpdk.org/doc
• For information about this Readme file and DPDK-Replay please write to [email protected]

2. Requirements

• A machine with DPDK supported network interfaces.
• A Debian based Linux distribution with kernel >= 2.6.3
• Linux kernel headers: to install type

	sudo apt-get install linux-headers-$(uname -r)

• Several package needed before installing this software:
  • DPDK needs: make, cmp, sed, grep, arch, glibc.i686, libgcc.i686, libstdc++.i686, glibc-devel.i686, python
  • DPDK-Replay needs: git, libpcap-dev, libpcap

3. Installation

3.1 Install DPDK

Install DPDK 1.8.0. With other versions is not guaranted it works properly. Make the enviroment variable RTE_SDK and RTE_TARGET to point respectively to DPDK installation directory and compilation target. For documentation and details see http://dpdk.org/doc/guides/linux_gsg/index.html

	wget http://dpdk.org/browse/dpdk/snapshot/dpdk-1.8.0.tar.gz
	tar xzf dpdk-1.8.0.tar.gz
	cd dpdk-1.8.0
	export RTE_SDK=$(pwd)
	export RTE_TARGET=x86_64-native-linuxapp-gcc
	make install T=$RTE_TARGET
	cd ..

NOTE: if you are running on a i686 machine, please use i686-native-linuxapp-gcc as RTE_TARGET

3.2 Install DPDK-Replay

Get it from the git repository. Remind to set RTE_SDK and RTE_TARGET.

	git clone https://github.com/marty90/DPDK-Replay
	cd DPDK-Replay
	make
	cd ..

4. Configuration of the machine

Before running DPDK-Dump there are few things to do:

4.1 Reserve a big number of hugepages to DPDK

The commands below reserve 1024 hugepages. The size of each huge page is 2MB. Check to have enough RAM on your machine.

	sudo su
	echo 1024 >/sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
	mkdir -p /mnt/huge
	mount -t hugetlbfs nodev /mnt/huge

4.2 Set CPU on performance governor

To achieve the best performances, your CPU must run always at the highest speed. You need to have installed cpufrequtils package.

	sudo cpufreq-set -r -g performance

4.3 Bind the interfaces you want to use with DPDK drivers

It means that you have to load DPDK driver and associate it to you network interface. DPDK-Replay sends traffic to all the interfaces bound to DPDK by default. Remember to set RTE_SDK and RTE_TARGET when executing the below commands.

	sudo modprobe uio
	sudo insmod $RTE_SDK/$RTE_TARGET/kmod/igb_uio.ko
	sudo $RTE_SDK/tools/dpdk_nic_bind.py --bind=igb_uio $($RTE_SDK/tools/dpdk_nic_bind.py --status | sed -rn 's,.* if=([^ ]*).*igb_uio *$,\1,p')

In this way all the DPDK-supported interfaces are working with DPDK drivers. To check if your network interfaces have been properly set by the Intel DPDK enviroment run:

	sudo $RTE_SDK/tools/dpdk_nic_bind.py --status

You should get an output like this, which means that the first two interfaces are running under DPDK driver, while the third is not:

Network devices using DPDK-compatible driver
============================================
0000:04:00.0 'Ethernet Controller 10-Gigabit X540-AT2' drv=igb_uio unused=
0000:04:00.1 'Ethernet Controller 10-Gigabit X540-AT2' drv=igb_uio unused=
Network devices using kernel driver
===================================
0000:03:00.0 'NetXtreme BCM5719 Gigabit Ethernet PCIe' if=eth0 drv=tg3 unused=igb_uio *Active*

NOTE: If for any reason you don't want to bind all the DPDK-supported interfaces to DPDK enviroment, use the dpdk_nic_bind.py as described in the DPDK getting started guide.

5. Usage

To start DPDK-Replay just execute ./build/dpdk-replay. If not specified it uses all the port bound to DPDK drivers and will send the same traffic on them. Root priviledges are needed. The are few parameters:

	./build/dpdk-dump -c COREMASK -n NUM [-w PCI_ADDR] -- -f file [-s sum] [-R rate] [-B buffer_size] [-C max_pkt] [-t times] [-T timeout]

The parameters have this meaning:

• COREMASK: The core where to bind the program. It needs 2 cores
• NUM: Number of memory channels to use. It's 2 or 4.
• PCI_ADDR: The port(s) where to send. If not present, it sends the same traffic to every port.
• file: input file in pcap format
• sum: when using multiple interfaces, sum this number to IP addresses each time a packet is sent on the interface.
• rate: rate to send on the wire. If not specified it sends at wire speed.
• buffer_size: Internal buffer size. Default is 1 Milion packets.
• max_pkt: quit after sending max_pkt packets on every interface.
• times: how many times to send a packet on each interface. Default is 1.
• timeout: timeout of the replay in seconds. Quit after it is reached.

The parameters before -- are DPDK enviroment related. See its guide for further explaination.

Here some example of command lines:

• It starts replaying capture.pcap on all DPDK interfaces at wire speed.

	sudo ./build/dpdk-replay -c 0X02 -n 4 -- -f /mnt/traces/capture.pcap

• It starts replaying capture.pcap on the two specified interfaces at 8 Gbps on each link.

	sudo ./build/dpdk-replay -c 0X02 -n 4 -w 2:00.0 -w 2:00.1 -- -f /mnt/traces/capture.pcap -r 8

• It starts replaying capture.pcap on the two specified interfaces at wire speed. On the first interface, 1 is added to source and destination IP address, on the second one 2 is added.

	sudo ./build/dpdk-replay -c 0X02 -n 4 -w 2:00.0 -w 2:00.1 -- -f /mnt/traces/capture.pcap -s 1

The system approximately each one seconds prints statistics about its performances.

Rate:   10.000Gbps     1.319Mpps [Average rate:    10.000Gbps     1.319Mpps], Buffer:   89.998% Packets read speed:    0.333us