ucsd-e4e / asm-docs Goto Github PK
View Code? Open in Web Editor NEWAye-aye Sleep Monitoring Project Documentation
asm-docs's People
Contributors
Stargazers
Watchers
asm-docs's Issues
SYS.8.B: The router shall be able to automatically configure the network and dynamically provision endpoints to multiple IP Cameras (2) and Raspberry Pi 4s (3).
SYS.15.A: This housing shall provide protection against the aye-aye’s claws and teeth
On Box Assy Rev XA06
System Reliability Requirements
lens hole too tight
Lens hole for ASM On-box lens hood is too small - increase to fit lens
Pi Camera Focus Procedure
Need to define a procedure and determine parameters
SYS.16.B: This housing shall provide a port for the IP Camera (2)
SYS.15.C: This housing shall mount the Pi IR Camera (4) and NIR illumination such that the camera has a clear view of the nest box and aye-aye
SYS.4.A: The Pi IR Camera shall transmit video to the Data Server (1) via the Router(8) and the Raspberry Pi 4 (3)
Initial Hardware Build
SYS.16.A: This housing shall provide protection against the aye-aye’s claws and teeth
SYS.8.D: The router shall be able to automatically reconfigure the network from an unplanned power down.
SYS.14.B: This housing shall provide strong mechanical coupling from the nest box to the Arduino Nano BLE Sense (7).
Initial System Design
SYS.5.B: The USB Sound Card shall provide a digital signal at a rate sufficient to detect aye-aye vocalizations.
SYS.6.A: The Microphone shall pick up sound from the aye-aye’s nest box and feed it to the USB Sound Card (5) via the Coax cable (13).
SYS.17.A: This Raspberry Pi 4 shall forward data from the IP camera to the Data Server (1)
HW: Need to create post-processing drill table
as title
SYS.8.C: The router shall be able to automatically reconfigure the network as more units are added to the network.
SYS.16.C: This housing shall mount the IP Camera (2) such that the camera has a clear view of the enclosure areas
Timestamp Format
As a developer/user, I would like to be able to determine when and where a particular data was generated.
SYS.15.B: This housing shall provide a port for the Pi IR Camera (4) and NIR illumination
On Box Rev XA05
SYS.2.A: The IP Camera shall transmit video to the Data Server (1) via the Router (8)
SYS.14.C: This housing shall provide the necessary protection to the power supply for the Arduino Nano BLE Sense (7).
HW: Pi Camera M2 holes failing during installation
M2 holes need more material on the inside
HW: Lens Enclosure thread size
Too tight, recommend increasing to 2.26mm
SYS.15.D: This housing shall provide the necessary protection to the power supply for the Raspberry Pi 4 (3)
HW: ASM On-Box Base Plate too thick
XA0 base plate too thick, reduce to 3mm
SYS.5.A: The USB Sound Card shall digitize the signal from the Microphone (6) and stream it to the Raspberry Pi 4 (3).
Bench Configuration 1.0.2
Need list of stuff to get from Ian
Power Supplies Outside of Box for Remote Sensor unit
In the cabling diagram it currently shows the power supplies inside the box however our current configuration is that the are connected to AC outside of the box. The only thing that is in the box is the RPI.
Remote Sensor Node not saving data
Set up:
- Set up Remote Sensor node and Data Server
- Run Remote Sensor
Current behavior:
- Data Server recognizes Remote sensor node connection
- Data Server gets RSU heartbeats
- No ffmpeg output
Desired behavior
- Connection established
- RSU heartbeats
- FFMPEG file output
HW: Pi camera rear screw interference
Need at least 1mm more radial clearance
SYS.4.B: The Pi IR Camera shall have a FOV wide enough to cover the bottom of the aye-aye enclosure.
SYS.16.D: This housing shall provide the necessary protection to the power supply for the IP Camera (2)
SYS.8.A: The router(s) shall provide route data from the IP Camera (2) and the Raspberry Pi 4 (3) to the Data Server (1)
Need finger relief around the On-Box Sensor Unit's SD Card
Need to facilitate someone pulling out the card. Add cutout of thumb size for top/bottom access.
SYS.6.B: The Microphone shall have a characterized frequency response.
SYS.14.A: This housing shall provide protection against the aye-aye’s claws and teeth
System Security
Linux Box Setup for Data Server Prototyping
HW: Nano microUSB doesn't fit
microUSB holder needs to be .05 in deeper. Zip tie hole needs to be 0.1 in further out, with additional support under microUSB connector. Zip tie hole needs more clearance, add 0.01 in clearance
System Usability
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.