clone from https://github.com/chewitt/linux branch amlogic-5.15.y， And will add some patches that I have collected, which can be used for the aarch64 openwrt firmware, or for general occasions such as armbian.
License: Other
This 5.15 kernel can be used by the s905l3a android system~
Have you verified this driver in orangepi-zero2？After I compiled, I found that I did not find that the device when linux booting，and driver was not running。
my dts：
&mmc1 {
vmmc-supply = <®_aldo2>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
uwe-bsp {
compatible = "unisoc,uwe_bsp";
keep-power-on;
data-irq;
//adma-tx;
adma-rx;
//blksz-512;
status = "okay";
};
};
my config
CONFIG_SPARD_WLAN_SUPPORT=y
CONFIG_SC23XX=y
CONFIG_AW_WIFI_DEVICE_UWE5622=y
CONFIG_AW_BIND_VERIFY=y
CONFIG_WLAN_UWE5622=m
CONFIG_SPRDWL_NG=m
CONFIG_UNISOC_WIFI_PS=y
目前5.15.100内核无法使用networkmanagger。
请大佬更新5.15.102内核，以解决networkmanagger无法使用问题，谢谢！
Hi , why you are remove rtl8189ES Driver Pack from your repo?
*** Preface ***
A friend of mine brought this tv box "X96 Max+" complaining of kernel panics the device catches when runs in the pure Linux mode not Android. I successfully used kdump on my Raspberry Pi 4 to debug kernel panics. But i still cannot run kdump & kexec on this Amlogic device, but first things first.
*** Main part ***
The full name of the tv box is Droidlogic X96Max_Plus2_T and the ethernet chip is Realtek RTL8211F as it's seen on Android by Device Info HW app. Device is Amlogic s905x3, kernel 5.15.60 (compiled with debug info)
I used meson-sm1-x96-max-plus-100m.dtb after installation and the triple of:
*meson-sm1-hk1box-vontar-x3.dtb
*meson-sm1-x96-max-plus-100m.dtb
*meson-sm1-x96-max-plus.dtb
and
dd if=/tmp/hk1box-bootloader.img of=/dev/mmcblk0 bs=1 count=442
dd if=/tmp/hk1box-bootloader.img of=/dev/mmcblk0 bs=512 skip=1 seek=1
and after all meson-sm1-x96-max-plus.dtb from flippy's post at ->
https://forum.armbian.com/topic/15376-methods-to-fix-x96-max-pluss905x3-gigabit-ethernet-problem.
Now that the device enters kexec reboot only with the flag 'kexec -s'
root@armbian:~# ls -l /var/lib/kdump/
drwxr-xr-x 5 root root 4096 Aug 7 08:05 initramfs-tools
lrwxrwxrwx 1 root root 39 Aug 25 16:29 initrd.img -> /var/lib/kdump/initrd.img-5.15.59-mxdbg
-rw-r--r-- 1 root root 8695258 Aug 22 19:07 initrd.img-5.15.59-mxdbg
-rw-r--r-- 1 root root 234 Aug 25 16:29 latest_sysctls-5.15.59-mxdbg
lrwxrwxrwx 1 root root 27 Aug 25 16:29 vmlinuz -> /boot/vmlinuz-5.15.59-mxdbg
kexec -l /var/lib/kdump/vmlinuz --initrd=/var/lib/kdump/initrd.img --dtb=/boot/dtb/amlogic/meson-sm1-x96-max-plus.dtb --reuse-cmdline -s
arch_process_options:178: command_line: root=LABEL=ROOTFS rootflags=data=writeback rw rootfstype=ext4 console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 nr_cpus=1 mac=9a:29:43:2d:ba:16
arch_process_options:180: initrd: /var/lib/kdump/initrd.img
arch_process_options:182: dtb: (ignored)
arch_process_options:185: console: (null)
*** Ethernet part ***
The First issue is that after kexec reboot ethernet doesn't work, but wi-fi works good. The normal boot of ethernet:
root@armbian:~# dmesg | grep ethernet
[ 7.905241] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found
[ 7.906442] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found
[ 7.912687] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock
[ 7.920641] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[ 7.925539] meson8b-dwmac ff3f0000.ethernet: DWMAC1000
[ 7.931505] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported
[ 7.938112] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported
[ 7.946270] meson8b-dwmac ff3f0000.ethernet: COE Type 2
[ 7.950694] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported
[ 7.957686] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported
[ 7.964124] meson8b-dwmac ff3f0000.ethernet: Normal descriptors
[ 7.969932] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled
[ 7.975706] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 23.555361] meson8b-dwmac ff3f0000.ethernet eth0: PHY [0.0:00] driver [RTL8211F Gigabit Ethernet] (irq=40)
[ 23.570472] meson8b-dwmac ff3f0000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 23.595648] meson8b-dwmac ff3f0000.ethernet eth0: No Safety Features support found
[ 23.602691] meson8b-dwmac ff3f0000.ethernet eth0: PTP not supported by HW
[ 23.619891] meson8b-dwmac ff3f0000.ethernet eth0: configuring for phy/rgmii link mode
[ 25.290397] meson8b-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
After a kexec reboot:
root@armbian:~# dmesg | grep ethernet
[ 5.826678] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found
[ 5.827894] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found
[ 5.834149] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock
[ 5.841912] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[ 5.847004] meson8b-dwmac ff3f0000.ethernet: DWMAC1000
[ 5.852981] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported
[ 5.859557] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported
[ 5.867705] meson8b-dwmac ff3f0000.ethernet: COE Type 2
[ 5.872141] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported
[ 5.879138] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported
[ 5.885575] meson8b-dwmac ff3f0000.ethernet: Normal descriptors
[ 5.891376] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled
[ 5.897156] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 5.905088] meson8b-dwmac ff3f0000.ethernet: device MAC address 9e:61:9f:bd:1e:aa
[ 20.959437] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[ 20.967352] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 32.808649] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[ 32.819560] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 33.142282] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[ 33.163931] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 33.281170] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[ 33.287109] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 33.331279] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[ 33.334375] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[ 33.417977] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[ 33.427303] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
The second issue is that the second kernel for kdump doesn't start, it just stops after these lines:
armbian login:
[ 234.915496] kvm: exiting hardware virtualization
[ 234.952516] pwrseq_simple sdio-pwrseq: Turning off mmc
[ 234.955323] kexec_core: Starting new kernel
[ 234.971860] Bye!
I think this post belongs to the topic of kernel debugging. Thanks in advance.
Hi, could you add LED module support on HK1 Box (S905x3). I have seen a modified dtb on the post (https://www.znds.com/tv-1200939-1-1.html) by adding following codes.
leds {
compatible = "gpio-leds";
status = "okay";
sys_led {
label = "sys_led";
gpios = <0x75 0x0b 0x00>; //0x75是bank@14的phandle，注意修改自己的
default-state = "on";
linux,default-trigger = "default-on";
};
};
zvfd {
compatible = "z,vfd";
dev_name = "zvfd";
status = "okay";
};
It works.
I know the LED display can be controlled by armbian-led or openwrt-led provided by ophub/amlogic-s9xxx-armbian. But it does not work for the Bule LED at the left of the display.
There have been many changes since the last 3 years that might fix the bugs on this chipset.
https://github.com/jwrdegoede/rtl8189ES_linux/commits/rtl8189fs/
Thanks.
盒子s905x，p212.dts
原电视系统，安卓3.14内核心中显示正常，设置如下：
internal_eth_pins {
amlogic,setmask = <0x4 0x3000000>;
amlogic,clrmask = <0x3 0x300000>;
amlogic,pins = "GPIOZ_14", "GPIOZ_15";
linux,phandle = <0x2e>;
phandle = <0x2e>;
};
armbian dts设置如下：
&internal_phy {
pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>;
pinctrl-names = "default";
};
刷armbian 选p212.dtb启动后，没有插网线时，网络连接指示灯亮起，插上网线指示灯熄灭，请怎么更改dts中的设置，使其显示正常？
for the tx3 mini-H Amlogic s905w series driver which uses the ssv6051 wifi driver in the rockchip driver https://github.com/unifreq/linux-5.10.y-rk35xx/tree/main/drivers/net/wireless/rockchip_wlan/ssv6xxx . Is it possible to add an Amlogic SoC driver?
Can you please add wifi driver for W522A?
The driver is here https://github.com/CoreELEC/w1-aml.
After install CoreElec Amlogic-ng version for my X96 Max plus 2101w, I can see the wifi adapter and connect to router successfully.
But the driver is missing in this repo.
Thanks.
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
An Open Source Machine Learning Framework for Everyone
Django
The Web framework for perfectionists with deadlines.
Laravel
A PHP framework for web artisans
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
Some thing interesting about web. New door for the world.
A server is a program made to process requests and deliver data to clients.
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
Some thing interesting about visualization, use data art
Some thing interesting about game, make everyone happy.
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
Microsoft
Open source projects and samples from Microsoft.
Google
Google ❤️ Open Source for everyone.
Alibaba
Alibaba Open Source for everyone
D3
Data-Driven Documents codes.
Tencent
China tencent open source team.