wolfgangmauer / vantelligence_connector

A MQTT connector for devices in your camper!

Connector

Config goes into this topic:

connector/config

Examlpe config

support:
- homeassistant
devices:
- name: Befehle
  id: command
  class: Command
- name: Bluetooth
  id: bluetooth
  class: Bluetooth
- name: HS-Can
  id: hscan
  class: Socketcan
  connection:
    bus: can0
- name: PWM-Controller
  id: pwmcontroller
  class: PCA9685
  connection:
    type: i2c
    bus: 1
  channels:
  - id: 0
    name: Test-0
    min: 400
    max: 2600
    scale: 180
  - id: 1
    name: Test-1
    min: 400
    max: 2600
    scale: 180
  - id: 2
    name: Test-2
    min: 400
    max: 2600
    scale: 180
- name: Analogsensor
  id: analogsensor
  class: ADS1115
  connection:
    type: i2c
    bus: 1
    interval: 3000
  values:
  - name: A0
    measure: 0+GND
    min: 0
    max: 65535
    scale: 1
    unit: l
  - name: A1
    measure: 1+GND
    min: 0
    max: 65535
    scale: 1
    unit: l
  - name: Abwasser
    measure: 2+GND
    min: 1400
    max: 14000
    scale: 78
    unit: l
  - name: Frischwasser
    measure: 3+GND
    min: 0
    max: 14400
    scale: 110
    unit: l
- name: Luftsensor
  id: luftsensor
  class: BME280
  connection:
    type: i2c
    bus: 1
- name: Helligkeitssensor
  id: helligkeitssensor
  class: BH1750
  connection:
    type: i2c
    bus: 1
- name: Bewegungssensor
  id: bewegungssensor
  class: MPU_6050
  connection:
    type: i2c
    bus: 1
- name: B2B-Laderegler
  id: b2b_laderegler
  class: Votronic_VCC_1212
  connection:
    type: serial
    port: "/dev/ttyUSBCharger"
- name: Solar-Laderegler
  id: solar_laderegler
  class: Ective_DSC
  connection:
    type: serial
    port: "/dev/ttyUSBSolar"
- name: Wechselrichter
  id: wechselrichter
  class: Ective_CSI
  connection:
    type: pins
    power_pin: 17
    mode_pin: 27
    data_pin: 22
- name: Dieselheizung
  id: dieselheizung
  class: Autoterm_Air_2D
  subscribe:
    temperature_current: connector/device/luftsensor/temperature/state
  connection:
    type: serial
    port: "/dev/ttyUSBHeater"
- name: GPIO-NEW
  id: gpio-new
  class: GPIO
  pins:
  - name: 'Relais #1'
    type: out
    id: 18
- name: GPIO
  id: gpio
  class: Pigpio
  connection:
    host: localhost
  pins:
  - name: Dashcam
    type: out
    id: 8
    inverted: true
  - name: Wasserpumpe
    type: out
    id: 12
    inverted: true
  - name: Kühlschrank
    type: out
    id: 16
    inverted: true
  - name: B2B Laderegler
    type: out
    id: 20
    inverted: true
  - name: Soundsystem
    type: out
    id: 25
    inverted: true
  - name: Relais 1
    type: out
    id: 0
    inverted: true
  - name: Relais 2
    type: out
    id: 23
    inverted: true
  - name: Relais 3
    type: out
    id: 7
    inverted: true
  - name: Wasserboiler
    type: out
    id: 14
    inverted: true
  - name: '230V #2'
    type: out
    id: 15
    inverted: true
  - name: Display
    type: out
    id: 24
  - name: Licht1
    type: pwm
    id: 5
  - name: Licht2
    type: pwm
    id: 6
  - name: Licht3
    type: pwm
    id: 13
  - name: Licht4
    type: pwm
    id: 19
  - name: Licht Dachluke
    type: pwm
    id: 26
  - name: Schalter Dachluke
    type: in
    id: 4
    inverted: true
  - name: Haupttaster
    type: in
    pull: up
    id: 21
- name: Soundsystem
  id: sound
  class: Pulseaudio
  controls:
  - name: Main
    id: Master