crazyming / copter-gcs Goto Github PK

I tried to connect with bule snirf gold directly 

BSG          APM
Tx------------Rx
Rx------------Tx
GND-----------GND
VCC-----------VCC

BSG            BSG
CTS------------RTS

I have buad set to 5600 KBPS and its showing link active but is not displaying 
any data from APM....
I have selected MAV

What steps will reproduce the problem?
1.Arducopter 2.5.3
2.
3.

What is the expected output? What do you see instead?

Link is aktiv, but status says no data

What version of the product are you using? On what operating system?
aktuell

What steps will reproduce the problem?

1. Run the application copter GCS
2. Touch nothing and wait around 2 seconds

What is the expected output? What do you see instead?

I nice running app, instead I get a crash and the message "The application 
Copter GCS (Process com.bvcode.ncopter) has stopped unexpectedly. Please try 
again."

What version of the product are you using? On what operating system?

copter-gcs-9-packed.apk Mar 28 284Kb. Downloaded and installed directly from 
this site. Running on a Samsung Galaxy Tab 10.1, Android 3.1, pretty much 
stock, well other than a good rooting :)

Please provide any additional information below.

Tried a reboot, every time the exact same message. Only other point worth 
mentioning was at the time I was trying to see if the software would ID an 
FT232 device connected via USB. So I selected the USB connection option within 
the software. Unfortunately I both updated my previously working version of 
Copter-GCS and tried the USB option simultaneously, so I cannot be sure which 
if any is causing the problem. 

I get the same error with "copter-gcs-8-packed.apk".

What steps will reproduce the problem?
1. Setup -> PID 
2. Select field
3. Type value using on screen keyboard

What is the expected output? What do you see instead?
Value changes until you hit save. It then goes back to the original value (no 
change). Value should change and stay changed after hitting save. Using Android 
3.2.1 (tablet) and 2.3 (phone).

What version of the product are you using? On what operating system?
Latest release in downloads section.

Please provide any additional information below.
+ or - .1 and .01 work fine however while testing the quad, I prefer to set 
things like the I maxes to 0. This takes a looong time when its at 1500.

What steps will reproduce the problem?
1. Run Copter-GCS together with ArduStation/Mission Planner
2. Do normal mode switching via radio
3. Compare output of ArduStation/Mission Planner and compare what was set on CLI

What is the expected output? What do you see instead?
Output were swapped with each other
RTL <> CIRCLE
ALT_H <> SIMPLE

What version of the product are you using? On what operating system?
copter-gcs-5-packed.apk 

Please provide any additional information below.

Depending on screen size, the HUDs text is not in the correct position

request to add legends to the readouts tab

Hallo,

do you work on an update to the newest arducopter version,
because there are no more D parts and so on. Only P and I and IMAX!!!

This Programm is perfekt. Thx

No sanity checks to make sure values sent to quad (in MAVLink) are sane.
Failure to do so can lead to dangerous results with the quad.

Remove props when calibrating for now

When in forced portrait mode, the GPS and mission views cause a crash.
Due to double loading of activity. 

Hi, first of all, thanks for your amazing contribution to the community. I have 
followed your steps for the copter link and it works perfect with my PC Windows 
7. It works on my Samsung Captivate with rooted ROM ICS but it force closes. 
And on my Acer Iconia A500 with stock Android 3.2 Gen2 it links but it says no 
data. Any help or guidance would be great. Thanks.

Please provide any additional information below.

I am using version 9, with arduplane 2.6.

What steps will reproduce the problem?
1.after heartbeat is confirmed, open Mode Selection.  Wait 1 second and C-GCS 
errors and closes
2.in the Mission Planner screen, choose yes to retrieve mission from arduplane.


Please provide any additional information below.
I'm using gingerbread, and a Bluetooth bridge.  Many other features of C-GCS do 
not work well, but I assume that this is because I am using it with arduplane 
instead of arducopter.

Wouldn't a universal android GCS be amazing?  I'd love to help generalize it 
and fix the bugs!!!

Subject says it all.
Android phone may be stationary and keep the same IP over time - using DynDNS 
it's easy to know it's IP.

UAV with Dronecell, could start an TCP session to Android on a predefined port.

I'm still in mailcontact, but perhaps someone has the same problem:

I'm bought on Android Store the app. After mailing with the developer i 
uninstall the app and install it directly via link (version 9 with mavlink 1.0).

I'm using the new Asus TF700T with Android 4.0.03 and connect via BlueSmirfGold 
to 3DR air-module. On APM2 is the arducopter 2.6 installed with the same 3DR 
ait-module. Both 3DR and BT-module are set to 567k baud. The 3DR is like this 
picture configured and connected to APM2: 
http://code.google.com/p/arducopter/wiki/3DRadio#Configuring_using_the_Mission_P
lanner

Now, if I connect my 3DR-air-module for ground via FTDI-USB cable to my desktop 
pc, I can select the USB-Cable-Com-Port with 57k in mission planner and can see 
and set all data. It works fine.

Then I connect the 3DR-air-module for ground like the circuit diagram (from 
gcs-copter) with BlueSmirfGold and an IC to create the exactly 3,3 power 
supply. I've paired the FireFly.

Then I powered the 3DR and BT up. On 3DR the green led lights solid and the red 
led blinks. The BT module lights red. When I start the app, I selected MAVLink. 
The text "Protocol selected" shown, the green led by BT lights and the "Quad+ 
GCS Link" goes to task. If I press "Status", I don't get any data. In between 
times (SOMETIMES) the green and red led on 3DR blinks. I think, I've lost the 
connection. By click on "Readout" and then on "back" the program was closed by 
himself or android. 

Otherwise when the green led lights solid and the red led blinks for data, the 
app don't show me any data...

The connection doesn't lost, when I use the 3DR at FTDI-USB cable this is not 
happend. If I repower the 3DR module the green led is rapidly green solid and 
the red is flashing.

I no longer know...

Readouts activity crashes for some reason

Hello all,

i just devlopped a MAVLink Java code generator...
Entries are mavlink xml files.
Output are :
- messages classes (from messages tags)
- Interfaces classes (from enums tags)
- an IMAVLink class which implements all interface classes

So if you want use this result you must :
- implements IMAVLink in your MAVLink class and remove all inners classes
- i have refactor packages : chang com in org... :-)

My goal is to use your code in all Java plateform so it is staying a little 
stuff for that... :-)

I go in holydays for three weeks but you can email me to [email protected]

Have fun with this Eclipse project!

Best regards

Guillaume Helle

Hi Bart, any updates on the release date???

What steps will reproduce the problem?
1.ndk-build


What is the expected output? What do you see instead?
compilation of C coe.

What version of the product are you using? On what operating system?
head

Please provide any additional information below.
C code is throwing errors at compilation.

What steps will reproduce the problem?
Hi,
I'm a student of Politecnico di Torino (an Italian university).
My colleague and I are developing an integrated platform, consisting of a drone 
and an Android application, meant to manage the delivery of medicines in rural 
areas hard to be reached.
The drone has an APM 2.6 microcontroller.
Could you please help, providing the methods to send an Intent to your 
application, in order to open it, having the coordinates of the destination and 
the flying height already set up?
Thanks for your great work and for your time

What steps will reproduce the problem?
1. INSTALL version 9 can load anyting
2. install version 8 can use but can't loacd mission from UVA
3. Can't load arducopter1 protocal
4. using arducopter version is 2.7

Many mobile phone pixel to QHD 960X540
If the display is like the windows version of the APM PLANNER, is perfect

It got old, poorly HUD display works
will develop?

What steps will reproduce the problem?
1.Set new P value for PIT Rate 
2.I save
3.Save don't work

What is the expected output? What do you see instead?


What version of the product are you using? On what operating system?
APM 2.5 mavlink 1.0  - Samsung 10.1 GT-P7500

Please provide any additional information below.

is it possible to move the code base to GIT, that way it can be worked on and 
branched more easily

[deleted issue]

Make a setting to change the Bautrate.

thx
druckgott

is it possible to support usb OTG,
so we can connect the 3dr or xbee directly.
that will be cool~

What steps will reproduce the problem?
1. Try to compile the library
2.
3.

What is the expected output? What do you see instead?
Looks like a bunch of header files for MAVLink 1.0 are missing


What version of the product are you using? On what operating system?
The latest version from the git repository


Please provide any additional information below.
I did get it to compile by copying over all the header files from the 
arducopter library but the program still segfaults in the library.

When reordering the mission waypoints, the names update automatically, such 
that it is not clear that they were switched.

Sending more than ~7 MAVLink param_set packets causes XBee to drop packets

1.-add "Calibrate Compass" 
2.-add "calibarate gyro"

Hi, it would be nice if you could write something about arduplane compatibility.
Will it work partially with arduplane or mess things up ?

PID names are not friendly reading. Simply based on parameter name.

Should make human readable. Perhaps a lookup/conversion function.

The current mode selection screen has outdated modes for the labels.
Updateing of the labels is required.

When a mission waypoint is edited, the displayed name is not updated.