mkipcak / dwm1001-uwb-firmware

Custom localization and calibration firmware for Decawave's DWM1001 Ultra-Wideband modules

Firmware for UWB localization and anchor autocalibration using Decawave's DWM1001-DEV board

Custom localization and calibration firmware for Decawave's DWM1001 DEV ultra-wideband (UWB) development modules

Installation

1. Download Segger Embedded Studio (SES) version V3.34a (Note the version to ensure compatibility)
2. Download Segger J-Flash Lite and GNU ARM Embedded Toolchain 5.4 2016q3
3. Clone Decawave's code example from https://github.com/Decawave/dwm1001-examples.git

SES has a free license for nrF52832 development. Consequently, this IDE can be used without any limitation for DWM1001 development.

For more information regarding Segger Embedded Studio, please visit https://www.segger.com/products/development-tools/embedded-studio/

For more information about free license for nrF52832, please read https://www.nordicsemi.com/News/News-releases/Product-Related-News/Nordic-Semiconductor-adds-Embedded-Studio-IDE-support-for-nRF51-and-nRF52-SoC-development

How to program the devices

Follow these steps to load the initiator and responder firmware on the DWM1001-DEV boards.

Initiator

1. Open the project inside dwm1001-examples/examples/ss_twr_init but replace the files ss_init_main.c and main.c with the ones of the same name provided in the folder Initiator (inside of the Autocalibration or Localization folder depending on your objective).

2. Paste the file shared_var.h provided in this repository inside the folder dwm1001-examples/examples/ss_twr_init/SES/

3. Open the project in Segger, set the device ID to the desired value, connect the target device via USB and click Build and Run.

Responders

1. Copy the folder dwm1001-examples/examples/ss_twr_init and change the name to ss_twr_resp to identify it.

2. Replace the files ss_init_main.c and main.c with the ones of the same name provided in the folder Responder (inside of the Autocalibration or Localization folder depending on your objective).

3. Paste the file shared_var.h provided in this repository inside the folder dwm1001-examples/examples/ss_twr_resp/SES/

4. Open the project in Segger, set the device ID to the desired value, connect the target device via USB and click Build and Run.

Restore the factory firmware

In order to store the factory firmware, first download the .hex file from

https://www.decawave.com/wp-content/uploads/2019/03/DWM1001_DWM1001-DEV_MDEK1001_Sources_and_Docs_v9.zip

Extract the ZIP. You will find the .hex factory firmware file in DWM1001_DWM1001-DEV_MDEK1001_Sources_and_Docs_v9/DWM1001/Factory_Firmware_Image/DWM1001_PANS_R2.0.hex.

Open SEGGER J-Flash Lite (tested with V6.62a, the executable file is JFlashLiteExe) and choose the following fields:

1. Device: NRF52832_XXAA
2. Interface: SWD
3. Speed: 4000 kHz
4. Data File: DWM1001_PANS_R2.0.hex (downloaded following steps above)

Connect the DWM1001-DEV board to a USB port (we found some issues if you connect it after you start JFlashLite, so we recommend that you connect the dev board BEFORE starting JFlashLite). Optionally, click first on Erase Chip.

Click on Program Device. If you also erased the previous board, you should see the following output:

Connecting to J-Link...Connecting to target...Erasing...Done
Conecting to J-Link...Connecting to target...Downloading...Done

NOTE: The LEDs on the DEV board will be OFF while the firmware is being updated, do not disconnect the board until you see the Done message and the LEDs are flashing again. After erasing the device, you should see a single non-blinking red LED on the DEV board.