uavpal / beboptwo4g Goto Github PK

Shall I give it a try? Or stay way ?

Hi all I have installed and reinstalled the mod and no matter what I do I can't get the led to
Blue

When the aircraft lands automatically, the voltage measured at this time is about 10.6 volts.How to change the airplane code to 8.2 volts.So we can use 18650 batteries.Ask developers or experts to give answers.Thank you very much in advance.

is there a downgrade process for parrot Anafi ?

Successfully installed and flew soft moded bebop 2 using sky controller 2. However no luck with getting glympse/pushbullet to work. I had created accounts for both and entered the correct API key for glympse and created access token for pushbullet. I had read the FQA section and tried adding or omitting "+" or "1" to the config/phonenumber, no success. Do you guys have any other suggestions I can try for this issue. Your help will be greatly appreciated. Thank you.

Idea : Joining the SC2 and Bebop to a wifi router as clients and use the routers DOS protection and PMF protection to stop atrackers from disconnecting your drone and SC2. Since the bebop router wont do it.

SC2 can already be connected as client now all that is needed, is to make bebop 1 and 2 connect as client as in softmod

Or just find a way to enable the pmf option on sc2 and bebop radio broadcom_setup.sh ? Bcmwl commands

Hi,

I've maybe a problem with my firmware, when i try to connect my drone to my phone app FreeFlight, i don't see my drone.

Whereas my drone's wifi is connected, i don't understand what is the issues. So i tried to restore to another firmware.

They are already stored to "Internal_000" folder, the next step : launch the install with Putty but what command write ?

Thanks You

Hi, I have a question, why after removing the card from the modem there is no normal .mp4 file, but only two files (Bebop_2_2021-07-07T205726 + 0200_E01BF0.mp4-encaps.dat) and (Bebop_2_2021-07-07T205726 + 0200_E01BF0.-encaps.tmp) where the 1 is 505 KB and the other 2 GB. I have tried everything and nothing recognizes the video.
I am counting on some help :(

I have a bebop drone with Skycontroller 2P. I use my apple 11xr iphone for both the personal hotspot and freeflight pro app and Glympse app using the 4G mod. The modem is Huawei E3372 510 on an ATT network; the iphone is also on ATT. The glympse tracks the iphone and not the drone.
The number I used on the Glympse app is the iphone number; the phone number associated with the modem is a different number. For the modem I am using data only service. The freeflight pro seems to work OK but not the glympse app. Should I use the number associated with Modem instead of the iphone number? Will the glympse work with a data only service on the modem?

The Bebop 2's 4G/LTE USB modem should show a steady LED (indicating Internet connection) after about one minute.

The led is still flash. Internet connect is fail.
Modem: E3372H
Version: New
The 4.4.2 version is no problem.
Any suggest to check it.

Firmware4.4.0edition Although older, it is possible to change the cut-off voltage within the system. I would like to ask, is it possible to use this version to change 4G flight?

Hello from France,
I'm sorry for the translation in advance. I installed 4G on my Bebop 2 Power and it works perfectly well and I thank you for it. However, I cannot get Glympse to work on my Iphone 11. I receive a link from Pushbullet via Chrome with only ::
(Bebop2Power-000000's GPS location for information
You can track the location of your Bebop2Power-000000 here: https://glympse.com/)

I updated the uavpal_glympse.sh file.
My problem being that I am not receiving any position link from my bebop.

Can you help me please ?

Best regards

i did everything what i read in this site and finally find out zerotier doesn't work... please help me. i want to fly with LTE connetion and fly far more than 1.5kms

Hi,
Updated files to my bb2 and sc2. Glympse now works. But my skycontroller doesn't connect to my hotspot. SSID, WPA and Zero tier ID have been verified to be correct. BB2 connects to Zero tier without any problems. Any help would be appreciated. Thank you.

How to change the height of automatic return from 20 meters to 100 meters?Who can change in firmware? Please contact me at [email protected] , I am willing to pay.

After softmod installed. My bb2 always reset it's mac address once it's connected to 4g. So I have to get back to my ZT network and config it's new profile and assign a new IP before each flight.

Hello

I have a BB2 Power edition and all work well but the RTH dosent work. The drone go at an alititude to 2 meters from the ground and do nothing more.

Exemple : I go to a church from my home ~1 km I push RTH and the drone dont come back and go to 2 meters altitude...

Maybe I do something bad or I need to install the prog again ?

Thanks for your futur help !